The fuel pump should run for 2 seconds when you key it up. Does this bike have an aftermarket ign. switch? This is an important question.
We limit access by GUESTS to protect our members from spam, hacks and trolls. Please register to gain access to all our resources.
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Show posts MenuThe fuel pump should run for 2 seconds when you key it up. Does this bike have an aftermarket ign. switch? This is an important question.
Mine rattles louder with 10-40, so I always run 20-50. Transmission is quieter with 20-50, too. I don't like synthetic oils (many reasons, too many to list here) so I use Valvoline conventional 20-50 motorcycle oil. My 1500 has 249,500 Km on it.
Clutch basket wear. Mine has done it for years. Most noticeable when it's cold. Pretty much goes away after the engine is up to temp, but not completely gone. I have 155,000 miles on the bike, as of right now.
Shinko 777s. Google search. I'm running Kenda Kruz, very satisfied with the performance. You DO NOT want the original type Bridgestones....
Sorry, it was several years ago. All I remember was that it was a pretty easy thing to do, after I got the frozen bearing out and found that there was no case damage. Wish I could be of more help. I just told the parts guy to get me everything I would need.
I just had the parts man order everything to rebuild the pump. Bearings, shaft, seal, an so forth. The parts were still available, and probably still are, now.
Dumb question, but, since I can't see it, does it have a "tuner" installed? Try running it for a while with the r/s airbox cover off. Let it breath directly without the crossover restriction. Check the TPS voltage as per the service manual. One of the sensors is map, the other is baro. Do not connect a hose to the baro sensor. Have you checked the running fuel pressure? Lastly, does it have the correct ECM installed?
I know you have some weird laws in the U K, but that's a '99 "J" model. If you need parts for it, looking for '03 stuff will lead to disappointment and frustration. The tank, fuel system, frame and transmission internals are different on the "R" models (which would actually be an '03). Most things are the same, but not all. Good luck with it. I have 150,000 miles on my '01 "R" model. I had to replace the transmission bearings at 125,000, but that's all. All in all, it's been pretty bulletproof.
Condensate drain. Cars have them, too.
You should be lubricating the speedo cable core at least once a year.
I have 150,000 miles on my 1500. I remove the muffler when I change the rear tire (as shown in the service manual) and sometimes I run my Cobra Peace Pipe. Never replaced the goat bladder exhaust seals, just the header port seals
Yes, there is a rim strip, and the front tube requires a metal center valve, the rear uses a 90° metal valve. The front wheel is 3" in width, and the rear is 3 1/2" wide. The front tire is a 130/90-16, and the rear is a 150/80-16
This is going to come as a surprise to you, but the stock 1500 muffler has no internal baffles. The pipes are perf core with steel packing. I have had several stock mufflers over the years, and they are all the same. The muffler I currently have on the bike is a '99. The combination of the steel pack and the restricted air intake system create the muffled sound. Opening up the intake will increase the sound by a lot.
Makes sense. The TPS is used to control spark timing.
The engine cut-off switch, IE kill switch, and the side stand switch are both suspect.
Today, at approx 2 PM local time I turned over 150,000 miles on my 2001 1500 Drifter. Still runs like new, no oil consumption or leaks, and getting about 45 mpg. I'm planning a trip to the Dragon's tail for next Summer. I haven't been there since 2021.
When you change the ride height of one end, you need to change the height of the other end to preserve the correct rake and trail. If you don't adjust the front, you will destroy the handling qualities built in. I don't know how aggressive you are, but I drag stuff in corners on my 1500 and it's stock height.
Since the tank unit is accessed through the bottom of the tank, and it's a pretty labor intensive (and gasket replacement) job, I would just learn to live with it. The low fuel light will come on at about the 3 1/2 gallon mark, and that might turn out to be a better indicator of actual fuel level. You could completely empty the tank and then put in a measured amount. That would give you a good idea of where the gauge reads at any given time. When mine reads empty, it will hold 4 gallons to fill it.
Cross over tube won't fit through. To remove it, you have to either cut the end off, or remove the intake manifold. I found a spare on eBay and cut the end off mine. I have the spare one just in case some future owner might want to return it to stock.
I know I won't, but after the estate sale, somebody might want to...
You must have a J model. The R model requires tank repositioning to access the filler cap. The opening you see with the cap does not exist with the 5 gallon tank.
Not a waste of time. If I can help, I will.
The horns are hot all the time, the button provides a ground to complete the circuit. The horn system has it's own fuse and wiring harness.
The b/w wire is hot with then ign on, the other goes to ground through the switch. You will need a relay to make the single wire horns work
Front and rear cylinder spark plugs are fired by one coil. The engine will run with only one coil functioning. The waste spark system works like this: The cylinder with the burnable charge will get the spark, since the mixture is conductive. The other cylinder has exhaust gas in it, which is not conductive. When the spark energy reaches the firing tip, it ionizes the gasses in the gap. If the mixture will burn, it will allow the spark to jump. This system has been used for around a hundred years. My Camaro has waste spark, just like the Drifter. Dual tower coils, one tower fires the plug on one side of the engine, and the other tower fires the plug on the opposite side. There are 3 dual tower coils. The newer systems use one coil per cylinder, dedicated to just that plug.
Might seem an odd question, but....does this thing have a programmer on it? None of this makes any sense, unless there is a problem with the controller. Just another thought, because I can't see the bike: You wires the coils correctly? The twin plug system DOES NOT control one cylinder per coil, but rather one front and one rear. It should run on one coil, as long as it's splitting the spark between the cylinders. Decades ago, I dual plugged my 98 inch SuperGlide. Initially, I used two coils, one for the right side and one for the left. I replaced the ignition controller with a "single fire" system with 2 pickup coils. That let me run one coil for the rear cylinder, and one for the front. That allowed me to set the ign. timing separately for each cylinder, and use the full voltage from the coils to fire the plugs. The Drifter does not have a single fire system.
Page created in 0.161 seconds with 14 queries.