Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - indue

#1
Drifter 1500 only / rear shock alternative
February 18, 2020, 18:33:38 PM

I haven't been on the site for quite some time as I bought another bike but I thought I would give a plug for the Progressive 944 series shocks as I installed them on my Guzzi and they would work quite well on the Drifter. You can adjust the preload by hand and they lower the bike 1" but the shock has the same amount of travel as the 13" shocks. Progressive has a video on the subject. How do I like the newish Eldorado? It is quite remarkable as the engine has a lot of power and torque. It shakes a little at idle but once you get going it is super smooth (rubber mounted) and has great acceleration and awesome ABS brakes and cornering ability for a long wheelbase heavy bike. Also I might add, that the Dunlop American Elites are quite good and would be another good choice for a tire swap on the Drifter. I hope all you guys and gals are doing great!

#2
Drifter 1500 only / Re: Sold her
September 21, 2019, 17:45:30 PM

I have after I sorted out all the niggles. I sincerely hope that all you guys are getting enjoyment out of riding. It does not matter what bike you have just that you like the experience of riding...

#3

As i haven't been on here for some time, I thought I should make my final thoughts on this subject. The major problem with the bike had been in a gas tank liner that was failing and the big patches would interrupt the flow of gas. I had done the re-coating of tanks before so, I knew it would be a pain. It finally turned out that I had to completely strip both tanks' interiors. Needless to say, I got some stripper on top of the left tank so, now I had to re-shoot the top of the tank. Anyway it works great! You know how all bikes have there little idiosyncrasies, this bike is no different but it will get you there and back, just like the Drifter.

#4
Drifter 1500 only / Re: Old new guy
August 11, 2019, 17:40:07 PM

How does the engine work in neutral? Does it vibrate at certain rpm's? Do the rpm's vibrate more when you are sitting on the bike? Have you taken up to 4000+ revs in neutral and does it vibrate like it is going to disintegrate? If the motor does not display the symptoms at neutral/idle/increased rpm, then it is in the drivetrain either the transmission or the driveshaft/final. Check all fluids and grease in the components and renew if it hasn't been done recently.

#6

Well, here is an update. I had to take the bike into a mechanic because frankly I was stumped. I eventually put on a new carburetor (S&S) and that improved things but its low rpm/idle was very bad. I mean it would still run at higher rpm's but one would have to blip the throttle to keep it lit. So, I took it in. The head of the shop "Bob" has some notable accomplishments on the salt flats in a two engined Harley and on turbocharged Hayabusa's. And he has been working on Harley's for many years. So, some of the things he did: change the front sprocket to lower the rpms, a cracked manifold flange, a VOES which was missing which effects the timing at lower rpm's, a single fire coil instead of the dual fire that was on there, new valve cover gaskets, realign motor and shim the front brake. Well, after the work was done I took a trip up north to San Luis Obispo. The traffic was terrible the whole 300+ miles up there. I left early Sunday morning as that is the only time that you can transit LA relatively easily and I couldn't believe how bad 101 was past Santa Barbara. 4 lane divided and people racing in and out. On this bike you are somewhat at a disadvantage as you don't have instantaneous power. But it got me there. Not without a few hiccups and it does leak oil (something the Drifter never did) but not much although it blows back onto the bike so you have to carry a rag to touch up some of the chrome so it doesn't look like an old Triumph-just kidding! One thing that I noticed which kind of irritated me was the volume of the bike. It is a loud bike and even though I wear very good ear plugs it was still deafening. It would be more enjoyable long distance wise if it was toned down a bit. Another thing is that the vibration is quite noticeable but the bike does handle and take the bumps much better than the Drifter. However, the  Drifter's motor is better!

#7

I subsequently cut it down and it worked very well as I don't like helmet buffeting which in its full size (even though it had laminar flow up curve) I did get quite a lot of buffeting but when I cut it down it was excellent at least it was to me. I have sold the bike and maybe he will chime in whether it was good for him. Here is a picture of the cut down size. It was a National Stinger windshield.

#8
Drifter 1500 only / Re: Sold her
July 06, 2019, 14:16:32 PM

It turned out after putting the new carb in, it was a timing problem so, I just took it to Bob's Garage and being Harley guys they looked at it and ultimately fixed so now it runs right! Bob has set some records on Hayabusa's and on a double engine Harley on the Bonneville salt flats so, I guess he knows what is going on. The bike had a crack in one of the plates attached to the manifold, it was missing the VOES ( a vacuum electric switch effecting the timing), had a dual fire coil which it is supposed to have a single fire, checked the timing and adjust, shimmed the 6 piston front brake caliper that I had put on and put a different tooth front sprocket to lower the RPM's because it is too hectic at 70 mph. They did other things as check cable play, etc. and it was definitely worth every cent. Now it is time to ride those trips I had been planning. First shakedown is to the Central coast of California, San Luis Obispo, Morro Bay, Paso Robles. The only problem is transiting LA. Early Sunday morning is the only time to go up and Tuesday or Wednesday at 12-1 pm for the trip south. You do not want to be on the Ventura freeway (101) any other time. It is Hell on wheels!

#9
Drifter 1500 only / Re: Sold her
June 24, 2019, 12:25:20 PM

Well, I've ironed out all the fueling problems. Works pretty good. I notice that the engine runs better when it is thoroughly hot after about 10 miles. Finally rode it more than 60 miles-110 and it got me there and back! Pulled up to the gas station in Santa Ysabel and there was a guy with a beautiful fully restored Indian. I told him that it was a beautiful Chief and it was, however when I started riding, I thought that it might also be a Sport Scout as it was painted in the colors Fallon Brown and Indian red. Whatever it was, it was beautiful and started back up on the first kick. Very sorry to hear of the tragic accident in New Hampshire. I'd like to find out where the driver of the pickup truck is. His last name sounds like Russian collusion. Happy riding!

#10
Drifter 1500 only / Sold her
June 16, 2019, 16:11:44 PM

Well, about 4 weeks ago I sold the Drifter. She was an extremely dependable bike if one keeps up on the maintenance. My back is in not good shape and I just could not ride the bike anymore. Sold her to a very nice fellow about 45 miles north of me. He likes her quite well and had had a 1500 Vulcan in the past so he knew something about the bikes. Meanwhile I have been plugging away on the Harley as it had fueling problems that is, coughing and a flat spot between 2200 and 2800rpm. It is kind of disconcerting to have the bike on the freeway going 60-65 and it coughs like it is going to stall. So, after numerous times of changing jets, cleaning, soaking I just went ahead and bought a new S&S replacement. I still had to change the intermediate jet and up the size due to the ethanol in the fuel. To make a long story short, new tires, new oils throughout, PM 6 piston front caliper, new fork oil, rear rack installed, new battery, removed ape hangers and installed stock bars-whew!-all new cables, new spots and headlamp, new handgrips, new alternator and voltage regulator (American made), LED turn signals and rear taillight and probably some more that I can't remember. If I had taken the bike to Harley to have this done it would have cost a fortune! Now if I could just stopping working on it and go for a long ride...

#11

I had the same problem but it was due to my insertion of a viton o-ring in the wrong position. I had to pry the cap off. Unfortunately, I used some towels under the pry bar/screwdriver and it left a small dimple in the tank. If I had to do it again I would use a 1/4" piece of plywood with towels underneath. Then what I did after I took it off was to turn it over and drill two small holes through the retaining screw holes up and through the top of the cap. Then I used 4-40 screws and nuts to hold it together. The metal of the inside was somewhat tweaked so I also had to straighten that out. Once it was together, it worked fine. My key still worked in contrast to your predicament. Push down on the cap very hard and try to work your key again. Try a little penetrating fluid in addition to your graphite. If it doesn't work you will need to get it off so that you can replace it. Good luck!

#12
Drifter 1500 only / Re: radiator fan
May 03, 2019, 12:22:01 PM

The radiator fan does not operate all the time. There is a coolant pump that circulates the coolant and only when it reaches a certain temp (can't remember now but I believe it is in the service manual on this website) the fan switches on. Ride the bike in some traffic on a warm day and if it works it will go on.

#13
Drifter 1500 only / selling her
April 12, 2019, 13:24:02 PM

I am selling my Drifter because of my bad back. If anyone is interested she is on the San Diego, Ca Craigslist.

#14

This may not be a good comparison as I still have work to do on the Heritage namely, the carburetor needs to be looked after as the bike has probably not been driven in quite some time and I need to purge all the old gas. But here goes...Looks: both bikes are good lookers and actually I think the Drifter looks more authentic than the new Indian. The Heritage that I have has been made to look like an old bike of which the old Harley's particularly 1936-1963 I think are their best lookers. Engine: the Drifter motor is more refined and smoother and revs faster. The Heritage has quite a lot of vibration so, you really know you are sitting atop a V-Twin motor. But the motor works well. Maintenance: the Heritage requires a bit more as far as checking fluid levels namely, the trans and primary. Because the Drifter is unit construction it requires only one type of oil and the Heritage requires two, the primary and dry sump engine oil and the trans which is separate. As all of you know, you just have to check these things on both bikes. Drive: the Drifter has old style drive shaft nothing like the new BMW's and Guzzi's which are fully articulating. The belt drive on the Heritage works great and lasts a long time making it easier maintenance. Braking: I did put on a PM 6 piston front brake on the Heritage and new brake pads on the rear and they are not fully worked in yet but they will stop well so I don't have an opinion on that yet vis a vis both bikes. Ride: now here we get to the difference. The Heritage just rides and takes the bumps and the atrocious roads so much better that with my bad back this is a major plus. Trans: the gearing on the Heritage is a bit lower so you have to change gears a little bit sooner but, both are good shifters except on the Heritage it is quite difficult to find neutral. Handling: the Heritage handles better because (I'd have to look this up to confirm) it seems to have a shorter wheelbase and less rake making those U-turns and twisties a bit easier. Availability of parts: I really do like metric measurements but of course the Harley is English so there are a lot of proprietary parts on the Harley. How about 3/8X 32? That is all I can come up with because my bolt/nut measure does only 3/8X16 and 24. So, it is off to the Harley dealer to get a new one. Luckily, there are a gazillion Harley dealers around. I never had that problem on the Drifter as all of the metrics are standard. Dealer network is very good on Harley and I have one of the big one's within 5 miles and they are really nice people (not like yesteryear). Fuel consumption: I have not had a chance to analyze that aspect yet. Riders: Even though the Drifter riders don't number nearly as many as the Harley guys, I have never been one to buy anything because someone else has it. So, Drifter riders rejoice, you have an excellent bike.

#15
Drifter 1500 only / Re: Longevity
February 10, 2019, 16:17:48 PM

Nice going Paul. Did you grease everything up to last the next 100,000 km? You know, do it once, do it right and you will be riding into the sunset...

#16

Just put the rear rack on and will get the rear tire/wheel back today but am waiting on parts from Harley as the rear caliper bolts holding it on the bracket were history. Also, since the previous owner could probably not take one of the bolts out-star/Torx- he didn't replace the brake pads and they were down to 1mm. Belt is in excellent condition and wheel/spokes are good too. I put in an extra rim strip as just one is not enough in my estimation as I did this on the Drifter too. After I get the rear on, it will be time to put on a new front tire. I bought Conti Tour as they are steel belted with dual compound; hard in the center and softer in the outer for going around turns. One real plus and I don't know why more manufacturers do this is, to put drain holes in the front forks so you can change the fluid without having to take the forks off. My old Moto Guzzi has them and it is 49 years old!

#17

A ton of movies were filmed there particularly silent film swashbucklers and as I recall some of "Mutiny on the Bounty" (Clark Gable) was done there. All the Hollywood film stars went there through the early nineteen hundreds to the mid sixties. A lot of the stars had sailing vessels and since it is only 20 miles from Wilmington (LA Harbor) to Avalon it doesn't take more than several hours to get there-by sail that is. William Wrigley was the principle owner until somewhat recently and donated 99% of the island to the Nature Conservancy so no building can take place anywhere on the 99%. A good friend of mine who is also a sailer knew the captain of John Wayne's converted minesweeper "Grey Goose" and whenever Duke was in Avalon and my friend was there he would go over to Duke's boat and have some drinks with him. He said that Duke was a friendly, great guy and all AMERICAN!

#18

Just took a ride around the driveway and back to make sure everything is working, hand controls, new brake caliper, transmission, clutch cable etc. This bike is almost impossible to find neutral. Perhaps after riding it more it will reappear. The Drifter is almost too easy to find neutral. The clutch cable is difficult because you have to take the trans cover off to do it which also means you have to loosen the exhaust (at least on mine that does not have stock exhaust) and drain the trans fluid which has this little tiny Allen magnetic drain plug which is in finer thread than 3/8-24 possibly 3/8 -28-32(?). I found water contamination in the trans fluid so I cleaned it all out. All the other fluids are new and look great. Steering is different than the Drifter because the rake is different and wheelbase is a bit shorter. More stuff to do namely, tires and it is off to the races.

#19

The rear tire seems to be the biggest headache. A lot of brake dust and dirt accumulates after just 200 miles of riding. I use a degreaser with Bleche-white and a spoke brush. You have to do a portion on both wheels than move it forward and do some more etc. then wash them. Dry naturally or with compressed air. I have never used the Mr Clean but I will try it. An interesting story is that my ex-girlfriend swore that the "Mr Clean" character was fashioned upon a greeter on Catalina Island that was named "Duke" and was buffed with a bald head and ultra tan.

#20
Drifter 1500 only / Re: New Year, New Paint
January 21, 2019, 09:12:29 AM

Looks great!

#21

I don't know what the attraction is for those ape hangers other than to look like you are a 1%er. When I move the bike around- and it does weigh more than the Drifter- you simply cannot get much leverage to move it. The problem is that all the wiring is internal so, they had to be cut; plus they are too long for the switches on the stock handlebars. So, not only do I have to replace the bars but, I have to replace the clutch, throttle and brake cables. Luckily, in the picture I first ordered the 7 1/2" rise with 10" pullback and they are like roto tiller bars but did not spend much for them. So, I ordered the stock handle bars with a 4 1/2" rise and 5" pullback. They only type of bars left are the beach bars but I had them on my Gilroy Chief and I did not like them. The stock should work fine. The bike is painted like a '46 Knucklehead and runs/sounds great and it was had for $2000 trade in + $3995 cash. Somebody put quite a bit of time and money into this bike. I have had an EVO motor before and with a single carb (S&S) it is basically foolproof.

#22
Drifter 1500 only / Re: New Paint and tires completed
January 08, 2019, 09:15:43 AM

Looking' good!

#23
Drifter 1500 only / Got rid of one bike, bought another
January 02, 2019, 10:08:53 AM

In my old age I just simply could not ride my sport bike much anymore. It was very difficult to mount it with my bad back. So, I traded in the Suzuki and bought a Harley. Gonna keep the Drifter though as it is very reliable. I've got to do some things to the Harley namely, new rear tire, vintage rear rack after I remove the pillion, definitely get rid of the ape hangers, and some others. It is a 1991 Heritage softail done up to look like a 1947 Knucklehead as I have a picture of one with the same color/tank badge scheme. One thing, it definitely has the tone in spades.

#24
Drifter 1500 only / Re: Front tire pressure
December 17, 2018, 11:53:22 AM

32 front and 35 rear Metzler 888's.

#25

Definitely tube tires are what is on your OEM spoked wheels.

SMF spam blocked by CleanTalk