Modify message

The message has the following error or errors that must be corrected before continuing:
Warning: this topic has not been posted in for at least 180 days.
Unless you're sure you want to reply, please consider starting a new topic.
Last Edit: August 06, 2014, 08:44:26 AM by pcarrell
Attachments: (Clear attachments)
Restrictions: 6 per post (6 remaining), maximum total size 64.00 MB, maximum individual size 29.30 MB
Uncheck the attachments you no longer want attached
Click or drag files here to attach them.
(Clear attachments)
Other options
Shortcuts: ALT+S post or ALT+P preview

Topic summary

Posted by drifter-paul
 - August 06, 2014, 04:37:52 AM

Dear Pcarrell & Chief.

I like the V&H Bagger Dual Exhaust (Nomad) system (ZZ44032 on J&P) as the bulk emulates the original Drifter while having an exhaust each side , which is something I have always wanted.
I assume, from my reading,  that I can use a cross over pipe , bracket as per template in Mods, and a Classic/Nomad right passenger footpeg mount. If I don't need a PCIII /Cobra ,that is good, as I was worried about blue-ing.

Thanks for the great feedback.  :)

Posted by chief
 - August 05, 2014, 12:00:25 PM

The FI boxes are permanently mounted. With the PCIII you need maps and should really have the bike dyno'd to get the best result. With the Cobra they are set out of the box for certain pipes, but work with many others. POTS (potentiometers) are simply "knobs" / switches which adjust certain ranges of the box.

A pipe exchange usually doesn't require a FI box... but that is dependent upon the pipes. My Big Willys caused decel backfiring so I added a Cobra, made on adjustment and its been fine since (12 years). Try the change without the box... if there are indications you need one you can add it afterwards.
Posted by pcarrell
 - August 05, 2014, 08:17:37 AM

I know that you asked Chief about this, but if you don't mind a little outside input.........

I have the V&H Longshots on my bike with the stock air filter, and I can say that all I had to do was marble the engine to control popping on deceleration and it runs like a champ.  The stock exhaust is so restrictive that opening up the exhaust with these pipes just makes it breath like it should.  The popping was always going on with the stock system, but it was so restricted that you just didn't hear it.

There's 2 ways to cure the popping.  I marbled my engine as it's a 5 minute fix, but I'll give you links to both ways.

http://www.gadgetjq.com/smogstuffremove.htm

http://www.gadgetjq.com/rv_removal.htm

Now, I have both of my pipes on one side, but I don't think adding the 1 foot of extra pipe to cross the already shorter pipe over to the other side would change anything.  By doing that, essentially, both pipes are roughly the same length, so it shouldn't make a difference.

Maybe 49 will chime in, as he's the author of the tip in the mods section?  http://www.vulcandrifterriders.com/vhbag.html

Posted by drifter-paul
 - August 05, 2014, 08:03:30 AM

Chief,

I've been reading/searching this topic on the forum & the Mods section - and getting a little confused.

My old original exhaust neds replacing. I'm thinking Vance & Hines as they seem popular and have model specific pipes on their site.
I have done the toaster fix & removed the emission hoses. I have the original air filter and intend to keep it.

Do I need a Power Commander 3 or similiar when I fit the V & H, or is that only when I replace both the air filter & use the toasters.
If a PCIII is required,  is this unit permanently mounted, or is it a tuning tool to plug in and then remove when it re-maps the ICU -
(assuming this is what it does , or does it override the ICU and need to remain plugged in to the electrics ?)
With regard to Cobra instead  of PCIII - what are POTS ?
I'm assuming that if i need a PCIII, then I need to tune it in using a Dyno tester. Is this correct ?

Thanks

SMF spam blocked by CleanTalk