I have a 99 drifter trying to find a black light bar with black driving lights
Are there any options still available ?
GUEST? Registration opens up many more resources which are not available to guests. Registration is free, we never sell or give others access to your information.
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Show posts MenuI have a 99 drifter trying to find a black light bar with black driving lights
Are there any options still available ?
Mine is feb 1999 bike # 112
Well found my issue after finally getting back to working on the bike
It was the tip over switch .. it was apparently never bolted on and was laying upside down in front of the battery tray .. flipped it over and bolted up and purrs like a kitten again !!
Thanks for the info
I have a 99 Drifter
Will check A, B & C
I recharged original battery and replaced it as well
All,
Had my used to run like a top
I put it up on a jack stand for about 2 months removing tires/replacing, painting fenders etc ..
Finally got it all back together and tried to fire it up ... it started then died after about 10 secs ... after that it just turns over and does not even fire ... once in a great while if I let it sit for awhile and try it again it will start up run for a short time and die ..
I recharged and replaced the battery and that did not help
I hear the fuel pump turn on and build pressure every time
I also tried to start with bike in gear and clutch pulled in and it wont even turn over ..
Not sure if the kickstand switch is working or not .. Could that play a factor if it was damaged ?
I did twist the gas when trying to start it and likely flooded it ..
Any suggestions are welcome !!
Wondering if the Nomad 1500 dooleys will fit a 1500 drifter ? Also see some Vance and Hines for 1500 Nomad - go goat bladder and wonder if those would fit also
Any insights appreciated !!
Nevermind
It appears from looking at the 1999 1500 wiring diagram there is no connector in the main harness that connects to a headlight subharness ... the H4 headlight connector is directly from the main harness ...
Guess I can sell the 800 headlight sub harness ... jumped the gun too soon the get that went I don't need it
Previous owner hacked the wiring to connect a nomad/classic headlight, running lights and turn signals.
I got an OEM headlight and compatible 3 wire turn signals and acquired a drifter 800 sub harness that connects from the chassis to the headlight housing and hoping it is compatible with the 1500 ...
has connectors pictured below
Can anyone confirm ? Also guess I need the connector/adpater from the 3 wire connector to the H4 Bulb .. I assume the individual wires go to the turn signals (from what I see in the wiring diagram ..)
Thanks for the help !
Ended up getting a '99 main harness off Ebay pretty cheap .. looked like they were on it from what I could see plus I need a few other connectors for headlight and turn signals connections ..
Hi
Are the connectors to the 2 radiator sensors on the bottom of the radiator (for a '99) part of the main wiring harness ?
Thanks !
Just received my order of new OEM rear turn signal mounting parts (rubber grommets, metal sleeve and cap) and the K&S rear turn signals noted above fit perfectly ! So good news there ...
Just got the BikeMaster 262175 front turn signals in and they are 3 wire - so that's good !
Yeah thanks to Pilgrim who pointed that light bar out to me on Ebay !
Quote from: jamman on January 06, 2017, 18:22:13 PMThese just came in and look extremely close to the originals ... will use some diodes to wiring them up as running lights ..FYI - I found these and they seem to be a very close match on the originals
Rear:
http://cycleplicity.com/products/31273-k_s_technologies_25_2176_turn_signals.aspx
Got the original front turn signal bar coming and a headlight so it those will get back to stock ..
Would like to add the smaller amber 4" lights and the stock light bar .. any good source in black for those ?
Thanks ! the rubber is a bit cracked but maybe I can get the cheaper aftermarket ones and swap that out ..
I found these would have to paint them black and not sure they would fit the rear
You know of one that has 3 wires ?
FYI - I found these and they seem to be a very close match on the originals
Rear:
http://cycleplicity.com/products/31273-k_s_technologies_25_2176_turn_signals.aspx
OK yes I downloaded it .. thanks !!
Sorry what is a FSM ? thanks !
So from what I see the lower covers are not required as the dust/wiper seal fits over the top of the fork housing ..
I found some lower covers on the Bay and snagged them so I can get back to original ...
Now hopefully I can get the rebuild completed once all the parts arrive ..
Thanks
That covers the spring replacement and parts but how to disassemble the lower fork to replace the wiper seal and are the lower fork covers required ?
All
Recently acquired a '99 Drifter and the previous owner had leather covers made to go over the top of the forks, there are no lower fork covers on it ..
I detected that the front suspension needed work before I bought and I knew a rebuild would be in order .. I took off the leather cover and confirmed what I suspected that the seals are shot .. likely very low on oil
I have some progressive springs and fork seals (no wipers) on the way ..
Questions:
1) are the lower fork covers required ? Seems like they are given there is nothing to cover the open end of the tube to keep stuff out
2) beside a new fork seal and oil, any other parts needed from what you can see in the picture ?
Thanks !Page created in 0.097 seconds with 12 queries.