Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - rwantin

#1
Drifter 1500 only / Re: Sticking Clutch
May 12, 2017, 11:31:16 AM

That helps.  20/50 has been my standard but maybe not the best application here.  I always leave it in neutral and let it warm a bit while having a cig (not that one should smoke or anything).  ;D

#2
Drifter 1500 only / Re: Sticking Clutch
May 12, 2017, 08:22:55 AM

Thanks guys.  I did that, but will do it some more.

Thanks (again)!

#3
Drifter 1500 only / Sticking Clutch
May 11, 2017, 07:16:43 AM

Hi,

So I appear to have a sticking clutch issue, that is, it doesn't disengage after sitting a few days.  I did a search here and it was enlightening.  Got home yesterday, without starting it, pulled the clutch in and put it in gear - no release.  After a little more rolling back and forth encouragement, I managed to unstick it.

Based on what I have read, not an entirely uncommon thing.  The bike only has 6700 miles on it, so it sat (A LOT), and it needed some sorting (I have never seen clutch slave fluid so black before).

The bike has fresh Mobil 1 20/50 V-twin synth.  I read that someone mentioned using Kawasaki oil, and that it helped.  Worth trying?  And if so, what weight?  A shame with the fresh oil already, but if it will help.

Is there anything else I should do?  Clutch slave is flushed with fresh fluid, seems fine.

Thanks much, great forum here. 

#4

Hi Troll,

Stock exhaust, checked that early on (actually had the entire thing off), rubber bushings appear to be in good order - mounts solidly with a little movement, which I suspect is how should be.  I did the motor mount bolt thing (I think you suggested it in my other thread), but couldn't hurt to do again (not like it takes a lot of time).  I just removed the rear rack tying the two saddlebag rails together, just to try something with regard to vibration through the frame.

I wish I could dismiss as character (and heck, may reach a point where I do), but it does feel like going over a washboard at lower speeds (and at lower rpm static).  Seems pretty harsh.

You're a gentleman and a scholar, again, much appreciated.

#5
Quote from: CDNRatMan on September 19, 2016, 09:40:50 AM

Perhaps you might want to look at your rear wheel and the Damper rear hub shock, part # 92075-1121 see if it needs replacement. Just a thought.

I'll check it out, thanks!  Everything is on the table here.
#6

The thread that won't die.  I swear I am getting warmer, at least I hope!  ;D

I've been busy going through everything suggested in this thread.  Most recently, the fuel filter (brand new factory unit) and a rust-free tank.  I was actually encouraged by the crud that came out of the old filter, and hopeful that there might be the issue.

The bike runs fantastic (again, I LOVE this thing), but the washboard feel/resonance persists at low speeds/light loads.  The bike accelerates and runs at speed very smoothly.

I realize, out of some thirty bikes, that this is my first big V, so perhaps a small part of it is the nature of the beast.  But the resonance/washboard feel is pretty harsh.

The last thing would be the ujoint, but I'm not so sure as I can mimic the resonance with small throttle inputs (say, maybe 1500 - 2000 rpm) at a standstill.  That said, I'm thinking against the joint, at least for now.  It is possible it has tightened up (with only 6700 miles, the bike sat a LOT), but again, the stationary thing.  If I need to tear down the arse end I'll do it this winter.

I'll continue to run some Seafoam through it.  Another thought - service the injector/throttle body?  Thoughts?  Given the crud in the filter, perhaps it is compromised as well?

Appreciate it, and would like nothing more than this thread to die.

#7

Swapped the lines, added more gas, rode in to work today, all appears well (except for the vibration thing, but I'll keep working on it).

Just wanted to say thanks a ton for your help.

#8

Hi Troll,

There is a vent near the top of the tank, though I think that is outside the cap seal and just for slosh overflow.  I'll take a closer look when I get home.

The blue dot is the one I have capped off - in looking at your diagram, it possibly vents near the top of the tank.  If that is the case, it's worth trying to reverse it - cap the red dot (that is the one running gas to the ground), and venting the blue one.  Worth a shot.

And I really appreciate your help, sir.

#9

Thanks again.

It is definitely coming from the red-dotted outlet (the line that had the same resistance as the single outlet original tank).  That line, as with the original tank, runs to the ground.

#10

Sorry for the delay, this stupid work thing keeps getting in the way!

Should I try venting the second line to the ground?  Re-route it to the overflow vent to the upper part of the tank?

Thanks for your patience.

#11

Thank you.  That is very helpful.  Good to know on that sending unit line.  I was like, what the heck?

I have no problem with removing the tank.  The fuel does appear to be coming from the red return line which is routed down to the ground.  There is a line at the front of the tank up near the top which both tanks have (and I have hooked up), I'm guessing that's for slosh or overflow.

I noticed when swapping the pump both the the red and the blue have steel lines internally in the tank.

I'm studying the diagram - wonder what would work short of buying those evap components.  I'll have to think this through some more, and welcome any other thoughts.

Again, MUCH appreciated.

And I know I probably shouldn't worry about the bother thing - and get this is a forum.  It's just a weird one, and just my luck I ended up with a Cal-spec tank.

#12

Hi again,

And again, thanks for the guidance.

I attached a line and blew through the single vent on the original tank, with medium resistance.  Identified the exact same resistance on the new tank, and capped off the other.

All seemed well until I added some gas.  A small pool formed below the bike.  It stopped once I stopped adding gas and closed the cap.  The bike runs fine, and no gas from the bottom.  In some wishful thinking, I hope that was just from adding gas to a brand new tank.  I just stopped at the station to fill up, more pooling at the bottom of the bike, bigger.  I stopped before I could get two gallons in.

Rode it home, popped the cap, nothing.  Started it again, nothing.  Started it with the cap open, nothing.  It appears to happen only when I am adding gas.  So I am thinking along these lines.

-Swap the line?  This doesn't seem right, as the resistance is exactly like on the original tank.
-Vent the second line to the ground?
-Do something with this mystery line to the plastic cap on the sending unit?  Cap it?  Put it on the second vent?

Sorry about the bother, really want to make this tank work.  Any thoughts way beyond greatly appreciated.

#13

Thanks!  I'll give it a go today.

#14
Quote from: Troll on September 08, 2016, 18:45:15 PM

California emissions tank....You only need one vent to the atmosphere

Thanks!  Cap one off? 
#15
Drifter 1500 only / '99 1500 - Vent/Evap Line(s) - Help.
September 08, 2016, 16:10:25 PM

Hi, so I've been away a bit, and playing in the garage a lot.

I've been working on a vibration issue, something I posted a little while back (I'll follow up if this pans out).  Someone had suggest a fuel/fuel filter issue, which seemed to have some merit - there's rust in the tank (someone sadly had probably not stored properly), and what came out of the fuel filter wasn't pretty.

So as I was contemplating treating the tank (which has a few scratches, soft dents, and the aforementioned rust), I came across a brand new one, factory sealing, box, but with a dent, maybe a dealer take-off of some kind.  Knowing someone that could fix the dent (he did so perfectly), I bought it.  And I am thinking all kinds of awesome thoughts.

So I'm swapping everything out today and noticed something.  The NEW tank has TWO vent/evap lines at the back, the OLD one has ONE, and another line that strangely went to the cap on the sending unit.  I placed the sending unit cap on the old one for a visual.

Now I wish it was as simple as just placing both lines at the rear of the new tank (they are different diameters, the sending unit cap line being larger), but I don't think I could be that lucky.  Or if I am, please tell me so.  Do I cap one off?  I was in the shop manual, it shows two lines at the rear, but not what I have.  Strange.

I was grateful for all the advice on the previous post, and would welcome any here.  I'd love to get this back together again soon.

Thanks so much (in advance).

#16
Quote from: Troll on July 15, 2016, 19:01:01 PM

What year is your bike? The filter is inside the tank on the "R" model, and outside the tank on the "J" model

Fortunately, a '99 (J), so this should be a bit easier.
#17

Greetings Goose, and thanks for taking the time.

I have changed everything (including the rear diff) but the coolant thus far (looks as though it was changed recently, but noting the Honda stuff).  I think we're okay on the tires, I'm familiar with cupping (either on used bikes or my own commuting).  Changed oil with Mobil 1 Synth V-Twin, level is good (those little sticks with mirrors on them are handy).

I can duplicate vibration static (bike in neutral) with just a small pull of the throttle - the washboard effect is obviously more noticeable whilst moving.  I'm running seafoam through it and changing the filter this weekend - there is a small amount of rust in the tank which I will also be addressing - so looking forward to seeing if there's anything in the filter.

And then there is, well, just riding the thing more - weather and work have been fighting me a bit in this regard.

Again, this is a great group - and I hope to have this beast for quite some time.

#18

This thread will go away eventually, I swear!

Gave it a big shot of Seafoam this morning, and a filter is on the way.

Observation that may be meaningful.  I noted the washboard effect seemed diminished on the way in yesterday - it was in the upper 60's.  On the way home, in near 90-degree temps, it was back in full force.  Rode in this morning (about 70 out), and again, seemed to be lessened.  So air temp appears to at least be some sort of factor.  I'll stay the course with the Seafoam and new filter when I get it, does this suggest there may be some credence to a fueling issue? 

#19

Thanks a ton guys.

There's something I had not considered - I added some Techron to the first tank (always liked it for injection), so MAYBE as I'm burning through the gas, that could be the source of improvement.  I am also a huge fan of Seafoam (always have a bottle or two around), so I'll try that.  And a filter as well.  The bike fired right up when I got it, but it could have sat for some time prior.

Understood on the presence and big thumps, it's just that the washboard effect was, at least early on, pretty severe.  And wow, those miles are encouraging!

Appreciate it.   

#20

Following up a bit on this.  Just rode in this morning.

I did a few things over the weekend, interestingly, there was a noticeable improvement in the vibration on the way in to the office, but the washboard feel was still present, though again, improved.

I pulled and cleaned the plugs - they were pretty normal, don't think there's much here to do with it but noting.

The exhaust collector and clamps were one big ball of rust.  I pulled it, stripped, cleaned, new sleeves/clamps, made everything nice.  I noticed the rubber bushings, seemed like they were okay, and allowed a little movement, which I assume is good.  Of course, wondering if retorquing them helped in any way.  Side question - I like this exhaust, the way it looks, but is the Classic exhaust better?  Noticed one for sale this weekend and looks like it is an exact fit.

The other thing I was thinking about - I added a rear rack that came with the bike - I liked the idea because it ties the two saddlebag racks together and limits lateral movement.  Source of vibration?  Not sure.

In any event, despite the improvement, it's still there at lower rpm.  One thing I noticed - the resonance seems to be there even when the bike is stationary in neutral.  Of course, there's no tach, but I notice a vibration at guessing around 1500 - 2000 rpm.

Anyway, feels like I'm getting warmer.  And man o man, I love this bike.

#21
Quote from: CDNRatMan on June 24, 2016, 11:01:26 AM

Please do not tell me you have something more important than your Drifter vying for your time.....

The stupid work thing keeps getting in the way, I swear!  I know that doesn't make it right... ;D

Much to do this weekend!

#22

Thanks so much - will try the steering stem thing.

Haven't had much time to test anything, but will be back in the garage this weekend.

Really appreciate it guys.

-Robert

#23

Thanks again, guys.

I did check the tire pressures before riding - the rear was about 5 psi high - lowered to the unloaded spec of 36 psi.  As an experiment, maybe I'll add it back (yes, it's a pain back there).  Front was spot on.

Strange about the code on the front, double checked it, that was what was stamped on there, which is strange (must be REALLY fresh). :)  At the rear, it makes more sense - found 5113.  The receipt for the tires is less than two years ago.  They are Continental Milestones and still look pretty fresh (lots of numbs still).  They look like pretty good tires (I have had great luck with Continentals in the past).  They actually seem to corner pretty nicely.  Bike is fairly easy to toss around for a big 'un.

Thanks for the continuing education.  Seems like we are getting warmer.

#24

Thanks for the reply.

The date code (if I have this right) is 4316.  Not sure how to decipher (I think I USED to know how).  I'm now thinking maybe its engine speed (below), and somewhat encouraged.

So I rode in this morning, paying even closer attention to what was happening.  It SEEMED a little better after addressing the mount bolts, but realistically, probably just wishful thinking on my part.

Bike seems to smooth out a bit over 40, very nice at 50, particularly for such a large twin.  Below 40, particularly below 35 in third, the washboard resonance throughout the bike is pretty strong.  If I am accelerating say, in second, not so noticeable, letting off or shifting up into third brings the vibration.  I pulled in the clutch a few times and held the revs, still there.

This may be a big clue.  When I got to the office here, I revved it in neutral, a lot.  The resonance can be felt as the rpm drops lower, just as it is returning to idle.

Harmonic balancer?  Fueling?  It seems like we're getting somewhere.  And I can't tell you how much any insight is appreciated.

Pic at work - still a very proud papa.  Love this thing.

#25

Thanks Troll!  Yours was one of the threads I looked at while researching.  Thanks for chiming in.

Just returned from the garage (was out there before I saw this).  The frame through bolts were at maybe 15 lb-ft - adjusted them to 33 per the manual.  I will check the rubber grommets on the exhaust.  I did a cursory grab of the muffler - there's a little movement, not rixed overly rigid, which I'm guessing is appropriate.

It's definitely at lower speeds, seems to smooth out above 40.

I think I'll ride it to work tomorrow to get another read, maybe the frame bolts helped.  It's only a 7 mile surface street ride.

So maybe there's hope.  Thanks again.

SMF spam blocked by CleanTalk