Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - Tector

#1
General Discussion / BLACKED OUT WHEELS?
July 18, 2021, 15:40:49 PM

I like the look of my '99 Drifter, the blacked out version.  I'm thinking of having the wheels powder-coated black, to get even more of a pre-war Indian look.  Has anyone ever done this, and does anyone know where I can find an image of such a bike?  I'd like to have an idea of what it would look like, although I already have a pretty good idea.

#2

I finally got the rear crash bars (dresser bars, engine guards, whatever) installed on my 1999 Drifter 1500 today!  I think they look great on this bike, and will look even better once I've had them painted (black, like a lot of the other metal on these bikes).  Your mileage may vary.

They cost me $250 the set.  They are all steel, unfinished.  The guy who made them said that you can contact him (contact info below) if you'd like a set.  He could also have them powder-coated or painted (for a fee).  Presumably, shipping would be extra as well.

Russell Eisenhower is the source, at Superior Mobile Welding.  Website is superiormobilewelding.com.  E-mail is russ@superiormobilewelding.com.  He is also on facebook, apparently.

I hope the pictures come out.  If not, shoot me a personal message and I'll try to attach them to an e-mail.

I took the one picture from behind the bike to show how symmetrical they are (like the factory FRONT engine guards).  And I took one picture from above trying to show that each one angles slightly back from a line perpendicular to the long axis of the bike.  That picture doesn't really seem to show that aspect of them that well, likely because there is very little deviation from the perpendicular.  I took my (two-up) seat off the bike to make it easier to see these new rear guards.

#3

I FINALLY got the rear crash bars installed today.  I've started another thread ("AT LAST! SUCCESS! REAR CRASH BARS!") with the pertinent info.

#4

In my attempt to make rear crash bars (as had previously been available on this forum), I have found a fabricator, according to the plans I found, has bent an appropriate piece of tubing into the appropriate shape, and has fabricated the two brackets shown on the plans.  But neither of knows how the brackets attach to the tubing, nor how (and where) the brackets attach to the bike.  If anyone out there has a set of those brackets and can post or send pictures to give me some guidance, I would appreciate it.

#5

I met up with the local fabricator today.  He has a piece of tubing that is bent into the appropriate shape, and he has made the two brackets necessary for one bar.  But neither he nor I know how the brackets attach to the bar, or how the brackets attach to the bike.  So I'm looking for guidance (including on this forum).  Stay tuned.

#6

The guy who agreed to try making these bars has FINALLY gotten back in touch with me, and he thinks he has them ready to go.  I'm going to meet with him this weekend, and he's going to see if they will fit on my bike.  I will post an update after that.

#7

     Yes, I got the plans from Ted.
No, I don't yet know what they'll cost, and I haven't yet found anyone who will commit to making them, but I'm working on it.
Sorry, I don't know how these could be made for a Drifter 800.  (Those are great looking bikes, and I'd like to help, but that's above my pay grade.)
I don't have a solo seat rail on my bike, so I have nothing to use as a template for someone who might make them for me (I'm not someone who has that capability myself).
I will keep updating this post periodically to let all know if I find someone who can make these, and if so, what they will cost.

#8
Drifter 1500 only / ANY INTEREST IN REAR CRASH BARS?
March 07, 2021, 18:05:21 PM

I've obtained the plans for making rear crash bars for the Drifter 1500.  I am hoping to get a set for myself.  As might be expected, it would cost a lot to have someone make just one set, although I'm still checking with different fabricators to see how low a price I can get.  But I would like to know if anyone else out there would be interested in a set of these?  IF I can get them made (and that's a BIG if), I would figure on selling one set for $149, just like when they were previously available.  (That would be black powder-coated.  Chrome would be a good option for those with chrome Drifters, but that would require finding someone who can do the chrome plating, which may be tricky.)

So, please respond if you are interested.  I'll try to keep everyone informed on my progress with this.

#9
Drifter 1500 only / Uhaul bike trailer
March 07, 2021, 13:48:08 PM

I used a U-Haul motorcycle trailer to bring home my first Drifter (I've since sold it, but bought another).  They work great.  Simple way to go, with the built-in wheel chock in the front wall of the trailer, and plenty of tie-down points, and a tailgate that functions as a ramp.

#10
Drifter 1500 only / Brighter lights all around
October 31, 2020, 18:54:37 PM

In the interest of safety, I'd like to increase the light output on my 1999 1500-- I don't want to change any of the light fixtures, I'd just like to get more light output from each.  Does anyone have any recommendations for this?  By the way, in addition to the stock turn signals (front and back), tail/brake light, and headlight, I have the Kawasaki light bar (two spot lights).

I know that a common option is replacing incandescent bulbs with LEDs.  Which might work for the headlight, tail/brake light, and spot lights, but I have heard that they aren't a plug-and-play option for turn signals, since the current they draw is so much lower than stock that they make the signal flash much faster, making it tough for other motorists to "read" the signal.  But believe me, I am no electrician.  Which is why I'm looking for recommendations for plug-and-play options, if there are such.

#11

I recently bought a 1999 Drifter 1500 in great shape.  As purchased, it has the two-up seat and the saddle bag brackets, but it did NOT have the grip on the back of the two-up seat for the passenger.  I happen to like the looks of that grip, so I bought one (Partzilla).  Now, I can't for the life of me figure out how it attaches to the bike.

Can someone give me some guidance here, preferably a diagram?

There is a diagram on Parzilla that shows the support bracket for the rear of the two-up seat, and it shows the grip.  But it doesn't show the brackets for the saddle bags.  And in the service manual it shows the support bracket and the grip, but not the brackets for the saddle bags.

It looks like it would be simple to put the grip on that support bracket for the rear seat.  But I can't figure out how to do that AND get the brackets for the saddle bags on the bike.  And I know that I had all that on the 1999 Drifter 1500 that I used to own a couple of years ago.  (But that bike CAME with all that hardware on it, I didn't have to figure out how to attach it all.)

#12
Drifter 1500 only / Re: TORQUE SETTINGS
October 10, 2020, 19:28:05 PM

     TJ:
Many thanks.
Where is the pump air bleeder bolt?  Is that above the little drain bolt?
And where is the thermostat bleeder bolt?
To be honest, I never bothered with either of those when changing coolant on a Vulcan 1500 before (this is my fourth Vulcan 1500).  In fact, although I don't (yet) have a service manual for this bike, I don't remember the service manual mentioning either the pump air bleeder bolt or the thermostat bleeder bolt in the section about changing the coolant.  But perhaps I didn't notice or don't remember.
Again, thank you.

#13
Drifter 1500 only / TORQUE SETTINGS
October 10, 2020, 16:52:50 PM

Just under 2 weeks ago I bought my second Drifter 1500-- 1999, great shape.  The prior owner (owner #2) said that he didn't know when the last time was that anything had been done for maintenance, except for an oil change "2 or 3 years ago".  So it is currently standing upright in a wheel chock in my garage, with the oil and final drive oil and coolant all drained.  I don't yet have a service manual for this bike (just ordered one off eBay), but I'd like to get the bike buttoned up and back on the road in the next few days.  So I'm hoping someone can tell me the torque settings for:

A:  the oil drain plug

B:  the oil fill plug (or maybe there's no specified setting, as this is not critical)

C:  the bolt for the oil screen (at the bottom of the crankcase on the left side of the bike)

D:  the oil filter

E:  the final drive oil drain plug

F:  the final drive oil fill plug (again, not critical, might not be specified)

G:  the coolant drain plug at the bottom of the radiator

H:  the coolant drain plug at the bottom of the water pump (on the right side of the engine)

In addition, I know I need a new crush washer when putting the oil drain plug and the final drive oil drain plug back on the bike.  I don't think I need to replace the washers, gaskets, whatever, for any of the rest of the above, but if I'm wrong please set me straight.

Thanks.

#14
Where Can I Find/Buy/Trade / Re: Different exhaust?
October 02, 2020, 10:16:52 AM

Duh-- sorry.  I should have specified that my Drifter (like my first one) is a 1500.

#15
Where Can I Find/Buy/Trade / Different exhaust?
October 01, 2020, 08:50:12 AM

Just bought my second Drifter (I had traded in my first one, and eventually realized that that was a mistake).  1999 model, just under 9000 miles, great shape.  The windshield and seat are aftermarket, so:

ANYONE KNOW WHERE I CAN FIND A FACTORY WINDSHIELD OR SOLO SEAT OR TWO-UP SEAT?

Also:

I don't mind the original exhaust-- I'm not a "loud pipes save lives" type of guy.  On the other hand, I HATE that resonator (some people derogatorily refer to it as a "goat bladder", and I can understand the dislike)-- when I want to change the oil, it's RIGHT THERE IN THE WAY, making it very difficult to get the old oil filter off and the new one on.  So:

WHO STILL MAKES REPLACEMENT EXHAUST SYSTEMS FOR THE DRIFTER?

The only manufacturer I can find that is still making exhaust systems for a Drifter is Vance and Hines.  And I just might get one of their systems, to get rid of that damned goat bladder, even though their product is kind of pricey.  But I'm asking the Forum members so that I can reassure myself that I've left no stone unturned in my search for a new exhaust system, and maybe find a less-expensive brand (without a goat bladder).

Thanks.

#16
Drifter 1500 only / Re: Leaky gas cap
May 31, 2018, 08:41:04 AM

Thanks, everyone.  I'll try all these suggestions (or ask my service guy to look into it).  With all your help it seems that if I can't figure it out and fix it, it's my own damn fault.

#17
Drifter 1500 only / Leaky gas cap
May 23, 2018, 20:19:25 PM

I have a '99 Drifter that I love.  Although I live in PA and bought it from a guy in Maine, I've found that it is a California-spec bike (purchased in Arizona when new).  My only problem with it (aside from not enough time to ride) is that the filler cap on the gas tank leaks when the tank is full or near full.  I'm wondering if there is a problem with the emission controls on this bike, whether because it is California-spec or not, that is causing this.  I have two other Vulcan 1500s (2003 Nomad, 2008 Classic), both fuel-injected like my Drifter, that do not have this problem.  By the way, the Drifter has about 16000 miles on it.  To my knowledge, there has never been any damage to it, and the only modification I've made (so far) is to put Vance & Hines straight shots on it.

Any advice appreciated.

#18
General Discussion / Appearance of factory saddle bags?
October 23, 2015, 15:13:45 PM

I just bought a used 1999 Drifter, which I love.  When I first looked at the bike (before deciding to buy), it has a solo seat and no saddle bags; the previous owner said that it came with saddle bags, but he thought they were after-market.  Before I picked the bike up, I ordered (off the internet) a set of saddle bags that had been taken off another 1999 Drifter; those bags came with the struts that attach to a two-up seat (which I also bought), and the loops that attach to the struts.  Then when I picked up the bike, I saw that the saddle bags came with the same struts (no two-up seat, though), and the same loops, although each set of bags looks very different from the other.

So, my questions:  did Kawasaki offer factory saddle bags for the 1999 Drifter?  If so, what did they look like?  I don't need 2 sets of bags, so I'd like to sell one, but if either is factory, that's what I'd like to keep.

#19
Introductions / New member in Pennsylvania
October 07, 2015, 19:15:52 PM

I only started riding motorcycles (after taking the MSF course) in 2011.  I tried several motorcycles without finding one that I really liked (BMW, Moto Guzzi, Honda, Yamaha, the usual suspects).  Then one day, when browsing through Craigslist looking at Indian motorcycles, I saw a Drifter:  wow!, that bike was gorgeous!  AND, it had Kawasaki reliability, and a driveshaft, and electronic ignition, and fuel injection, and water cooling!  I confess, though, I got distracted:  in researching that bike, I found out that the Nomad is actually a better bike, at least on paper.  And I found a used Nomad that I just love (2003, Fi).  But I kept admiring those gorgeous Drifters from afar, especially the blacked-out early models.  I had had a sidecar rig built on a Moto Guzzi, to bring my grand-daughter on rides; Guzzis are great bikes, but I finally got tired of niggling little oil leaks, gauges that don't work, lights that don't work, etc.  So I found a sidecar rig built on a 2008 Vulcan 1500 Fi Classic, and ditched the Guzzi.  But I was still admiring those gorgeous Drifters.  Then last month (9/15), I saw a 1999 Drifter 1500 for sale when I was on vacation, and I bought it.  And again:  wow, that bike is gorgeous!  I'll try to post pics of all 3 of my Vulcan 1500 Fi bikes.

SMF spam blocked by CleanTalk