Post reply

The message has the following error or errors that must be corrected before continuing:
Warning: this topic has not been posted in for at least 180 days.
Unless you're sure you want to reply, please consider starting a new topic.
Attachments: (Clear attachments)
Restrictions: 6 per post (6 remaining), maximum total size 64.00 MB, maximum individual size 29.30 MB
Uncheck the attachments you no longer want attached
Click or drag files here to attach them.
(Clear attachments)
Other options
Shortcuts: ALT+S post or ALT+P preview

Topic summary

Posted by pcarrell
 - April 16, 2015, 18:10:37 PM

Now don't you go and blame your good behavior on me!

Posted by CDNRatMan
 - April 16, 2015, 13:48:19 PM

  I have a 30" inseam, and have no issues with the 800, and even better since I re did the seat and have it made to fit me. I would post pictures of my getting it right but PC might get offended and I am trying so hard to be nice to him.

Posted by MikeakaFred
 - April 16, 2015, 11:25:04 AM

No....LOL
I don't need a lowering kit but everyone with an inseam of 30"or less should consider a trade for this one...or just buying if from the guy above.  And there are different setting, front and rear, with Driftin'Girl's lowering kit.  Her's  had 1", 2" and a 3" lowering capablities on the front and rear.
When you see my BMW you'll see what disaster a too tall bike combined with short legs can cause !!

Posted by CDNRatMan
 - April 15, 2015, 08:07:43 AM

 :)   are you looking to lower your ride now Stumpy? The Missus bike easier to get on and off of?

Posted by MikeakaFred
 - April 15, 2015, 05:56:14 AM

They say a picture is worth a 1000 words. If you could post a pic it would save everyone shortening their finger tips.
Are there  two approx. 2 inch wide bars showing slightly below the rest of the bottom?  There are various kits  so seeing is the easiest way. The foot stand is a give-away.
You may also have a lowering kit in the front but we can get to that later.

Don't throw anything away...there will be a buyer waiting!

Posted by CDNRatMan
 - April 14, 2015, 17:18:43 PM

  Calling Driftingirl and Mike her mechanic they installed a lowering kit on her 800, his is still normal, so they will be able to tell you, I'll pm them to get them started on that.
Replacing the mono shock, which I did last winter did not raise the bike any, but it sure made a huge difference in the ride.

Posted by greenbarn
 - April 14, 2015, 17:07:35 PM

I wonder if someone has put a lowering kit on there?   If I understand, on the sidestand, it must barely tilt to the left, not enough to be "stable"?? (per your comment about blowing over)   If someone lowered it and did not shorten the stand, it would look like that.

I do not have, nor have seen, a lowering kit installed - but maybe someone that has one can tell you what to look for???

(((((Troll beat me to the post, but I'm posting anyway))))))

Posted by Troll
 - April 14, 2015, 17:06:20 PM

Sounds like it has a lowering kit installed. 800s are taller than 1500s..

Posted by Groatski
 - April 14, 2015, 16:24:43 PM

Hello,

I just bought a 2000 Drifter 800 (8600 miles), and one of the first things I noticed was that it seems to ride extremely low.  I find myself dragging the foot boards during moderately sharp turns, and when resting on its side stand I fear a stiff wild will knock it over.  Also the suspension seems overall to be soft and squishy.  I've read on this site how the rear monoshock can be adjusted, but after locating it I discovered that it's already at its firmest setting (setting #7).

Aside from replacing the rear monoshock (they cost close to $500!!) is there anything I can do to stiffen the ride and raise the ride height?

SMF spam blocked by CleanTalk