We limit access by GUESTS to protect our members from spam, hacks and trolls. Please register to gain access to all our resources.
Posted by DC
- September 12, 2016, 14:10:45 PMHopefully it's not a crack in the tank.
Posted by CDNRatMan
- September 12, 2016, 13:20:50 PM 
rwanting, please do not fret about asking questions, it just makes the 1500 crowd think and ponder, and they love a problem to solve....... 
Posted by rwantin
- September 12, 2016, 09:43:54 AMHi again,
And again, thanks for the guidance.
I attached a line and blew through the single vent on the original tank, with medium resistance. Identified the exact same resistance on the new tank, and capped off the other.
All seemed well until I added some gas. A small pool formed below the bike. It stopped once I stopped adding gas and closed the cap. The bike runs fine, and no gas from the bottom. In some wishful thinking, I hope that was just from adding gas to a brand new tank. I just stopped at the station to fill up, more pooling at the bottom of the bike, bigger. I stopped before I could get two gallons in.
Rode it home, popped the cap, nothing. Started it again, nothing. Started it with the cap open, nothing. It appears to happen only when I am adding gas. So I am thinking along these lines.
-Swap the line? This doesn't seem right, as the resistance is exactly like on the original tank.
-Vent the second line to the ground?
-Do something with this mystery line to the plastic cap on the sending unit? Cap it? Put it on the second vent?
Sorry about the bother, really want to make this tank work. Any thoughts way beyond greatly appreciated.
Posted by rwantin
- September 10, 2016, 05:13:51 AMThanks! I'll give it a go today.
Posted by Troll
- September 08, 2016, 19:54:22 PMBlow through each one and find the one that most closely works the same as the original tank, and seal off the others
Posted by rwantin
- September 08, 2016, 19:25:38 PMQuote from: Troll on September 08, 2016, 18:45:15 PMThanks! Cap one off?California emissions tank....You only need one vent to the atmosphere
Posted by Troll
- September 08, 2016, 18:45:15 PMCalifornia emissions tank....You only need one vent to the atmosphere
Posted by rwantin
- September 08, 2016, 16:10:25 PMHi, so I've been away a bit, and playing in the garage a lot.
I've been working on a vibration issue, something I posted a little while back (I'll follow up if this pans out). Someone had suggest a fuel/fuel filter issue, which seemed to have some merit - there's rust in the tank (someone sadly had probably not stored properly), and what came out of the fuel filter wasn't pretty.
So as I was contemplating treating the tank (which has a few scratches, soft dents, and the aforementioned rust), I came across a brand new one, factory sealing, box, but with a dent, maybe a dealer take-off of some kind. Knowing someone that could fix the dent (he did so perfectly), I bought it. And I am thinking all kinds of awesome thoughts.
So I'm swapping everything out today and noticed something. The NEW tank has TWO vent/evap lines at the back, the OLD one has ONE, and another line that strangely went to the cap on the sending unit. I placed the sending unit cap on the old one for a visual.
Now I wish it was as simple as just placing both lines at the rear of the new tank (they are different diameters, the sending unit cap line being larger), but I don't think I could be that lucky. Or if I am, please tell me so. Do I cap one off? I was in the shop manual, it shows two lines at the rear, but not what I have. Strange.
I was grateful for all the advice on the previous post, and would welcome any here. I'd love to get this back together again soon.
Thanks so much (in advance).