GUEST? Registration opens up many more resources which are not available to guests. Registration is free, we never sell or give others access to your information.
Posted by OR Seedman
- August 12, 2016, 17:38:56 PMthe standard bolts are 30mm long...another 4-5mm would be better...that's why I swapped one out on each side with the upper rear fender/bumper bolts. i don't think you can swap them all out since the seat bracket bolts are not threaded all the way...they don't quite thread in all the way on the bottom fender/bumper mounts....but one on each side is better than none....I will eventually replace them with new chrome ones when I can find them. Chrome flanged bolts long enough are proving difficult to source, though..
Posted by J.D. Beard II
- August 12, 2016, 08:26:47 AMI recieved my mounts, i must say they are awesome, nice coating, sturdy material, very pleased... i am going to fit them this weekend. What size bolts do i need to cover the extra length?
Thanks again OR Seedman for going the extra mile!
-J
Posted by OR Seedman
- August 09, 2016, 17:59:39 PMmine mounted right up. could be the powder coating in the holes...
I swapped out the upper rear bumper/fender bolts with the rearmost bolt on each of the seat brackets...this gave me a better bite on getting the threads started (longer by 4mm) It was hard to hold the mount with the saddlebag on it and get it lined up properly, but once I started the longer rearmost bolt first, it went much smoother...
If anyone that purchased a set from me has any issue, please let me know so I can make the adjustment at the fabricator for any new sets going forward...
Posted by cruzr8000
- August 08, 2016, 23:48:33 PMI bought a pair of mounts for the 800 from Osprey. I couldn't get them mounted because the bolt holes were about 1/8 inch too far apart. I had to grind out the bolt holes before I could get them to fit.
Posted by allstateguy
- August 04, 2016, 16:42:04 PMYay! Thanks Hagen for going the extra kilometer for your fellow Drifterers!
Posted by OR Seedman
- August 04, 2016, 16:11:41 PMpicked up the mounts this afternoon...gotta say, the powder coat paint is better than the originals by far....very pleased with how they turned out. as of right now, 4 sets of the 800 mounts are spoken for, which leaves 1 set available. I also have 2 sets for the 1500. I will use one of the original pieces on my set (not as nice paint), so that everyone else gets the better quality painted ones.....I will just have to touch it up a little.... 
I am going to put the remaining sets in the classifieds on here. However, I will also be posting them on Ebay at $25.00 higher per set to help offset the Ebay fees.
ride safe
OR Seedman
Posted by OR Seedman
- August 04, 2016, 15:19:21 PMThanks Mike...I appreciate the support. the mounts are suppose to done in a few....wow...they just called me and said they are ready...going to get them now
I will put the extra sets in the classified section with pics tonight..
OR Seedman
Posted by MikeakaFred
- August 04, 2016, 07:07:10 AMI'm happy to hear Seedman has picked up on these bag mounts. There is no reason to think his would be of any lesser quality than the previous manufacturer.
They are excellent quality and fit like a glove on my 800 and for the price, a true bargain ! I highly recommend them.
If you put a heat shield on the bottom of the right bag you can mount any brand bag within an inch of the exhaust pipe. It really doesn't get any better!
Mike in NS
Posted by J.D. Beard II
- July 27, 2016, 08:58:42 AMI will take a set for the 800 if you have a set available... please just send me a message on here and i will get you my information. Thank you and happy drifting!
-j
I almost forgot... zip is 67068 located in kansas. Thanks
Posted by OR Seedman
- July 24, 2016, 09:06:32 AMthey are 3/16th of an inch thick plus the powder coating.. the bent one is for the 1500 Drifter. it accommodates the rear shock and is side specific.
Posted by Ironworking
- July 24, 2016, 01:08:23 AMQuote from: OR_Seedman on July 23, 2016, 19:27:38 PMTY Seedman. One more question. What thickness is the metal and are they just flat? One looks bent.If you look at the pictures for the 800 mounts, you can see 2 holes on the skinny section. these bolt to the solo seat bracket on each side. Since they don't have the bend that accommodates the shock on the 1500, they are interchangeable for either side. I would suggest slightly longer bolts, though, as the bracket bolts are 30mm long and you should have at least a couple more mm in length for better bite on the threads due to the thickness of the metal mount. I tested a swap with the upper rear fender/bumper mounting bolts (they are 34mm) before I dropped off the one template at the machine shop. They worked great, but they are not chrome like the bracket bolts...they are stainless steel....I cannot find chrome flange bolts that are in the correct size (10x34mm or 10x35mm with 1.25 pitch), so I am just going to use the ones like I tested. if anyone else has an idea on that, let me know..
Thanks,
OR Seedman
Posted by allstateguy
- July 23, 2016, 22:15:57 PMthese are kinda spendy but they are flanged!
Posted by OR Seedman
- July 23, 2016, 19:27:38 PMIf you look at the pictures for the 800 mounts, you can see 2 holes on the skinny section. these bolt to the solo seat bracket on each side. Since they don't have the bend that accommodates the shock on the 1500, they are interchangeable for either side. I would suggest slightly longer bolts, though, as the bracket bolts are 30mm long and you should have at least a couple more mm in length for better bite on the threads due to the thickness of the metal mount. I tested a swap with the upper rear fender/bumper mounting bolts (they are 34mm) before I dropped off the one template at the machine shop. They worked great, but they are not chrome like the bracket bolts...they are stainless steel....I cannot find chrome flange bolts that are in the correct size (10x34mm or 10x35mm with 1.25 pitch), so I am just going to use the ones like I tested. if anyone else has an idea on that, let me know..
Thanks,
OR Seedman
Posted by Ironworking
- July 23, 2016, 16:34:08 PMQuote from: OR_Seedman on July 14, 2016, 21:39:13 PMokay..so I got 2 bids on making the Osprey type saddlebag mounts for both the 800 and the 1500. The 1500 has a bend in to to go around the shock...costs more to make. So before I plunk down $$$ to get some made, I would like to know if there is any interest in either or both. I can sell the 800 style on here only for $100 plus shipping and the 1500 style for $125 plus shipping. Shipping would be UPS ground from zip 97303. I am going to get an 800 set made for myself anyway...it will take about 3 weeks. they will be powder coated in black just like the originals. buyers to supply their own hardware.
If I make extra and put them on ebay, they will be marked for $150 and $185 respectively.....
Let me know if anyone wants a set at the Vulcan Drift Riders discount....I will be placing the shop order early next week (because I want mine asap), so I would like to do the extras at the same time...
Thanks
Can anyone show me how these are mounted on a 800? Thanks in advance. TIA
Posted by jack freeman
- July 21, 2016, 21:38:44 PMHello
your question about saddle bags 800 drifter ?
My 2002 800 has hard bags . scootworks bag brackets Wittco Bags 12 1/2 " H , 8 or 9 " wide you can view my drifter on this web site
WITTCO HARD BAGS.COM
My 2006 800 are Large universal slanted bags Viking bags 139.00 .They have many to choose from . these bags are very strong, no sagging
built very strong almost a hard bag. Easy to install, very nice look ona 800 drifter . Fit great on ospray brackets ( VIKING BAGS .COM )
HOPE THIS WILL HELP . PS. 2002 DRIFTER PHOTO SCOOTSWORKS PHOTO ALBUM ( GREEN VALLEY AZ ) Take a look .
THANKS JACK