Modify message

The message has the following error or errors that must be corrected before continuing:
Warning: this topic has not been posted in for at least 180 days.
Unless you're sure you want to reply, please consider starting a new topic.
Attachments: (Clear attachments)
Restrictions: 6 per post (6 remaining), maximum total size 64.00 MB, maximum individual size 29.30 MB
Uncheck the attachments you no longer want attached
Click or drag files here to attach them.
(Clear attachments)
Other options
Shortcuts: ALT+S post or ALT+P preview

Topic summary

Posted by Bucko
 - August 31, 2015, 18:12:27 PM

Thanks PC:

I ended up ordering a set of OEM fibre plates as the price was attractive (relative to other options - about half the cost of Barnett) and the original OEM clutch lasted 70k Kms before slipping (and the fibre plates might still be all right but I'm pretty sure the spring is buggered).

Posted by pcarrell
 - August 30, 2015, 08:59:27 AM

I've heard good stuff about the Barnett plates, but I haven't used them personally.

Posted by Bucko
 - August 29, 2015, 13:20:04 PM

Me again.  I went to the shop today and got all my parts lined up for the clutch rebuild.  I thought it would be wise to ensure I had all the correct parts and good thing I did as I found out I was sent the wrong Vesrah clutch fiber plates (they sent ones for a VN800).

So I have to re-order the fiber plates (just in case I need them) and thought I'd take this opportunity to solicit opinions on which are the best fiber plates to use these day, i.e. OEM, Vesrah, Barnett, EBC, Ferodo, etc.  Let me know your thoughts/experience.  Thanks.

Posted by Bucko
 - August 07, 2015, 17:01:45 PM

Thanks C.

Posted by chief
 - August 06, 2015, 13:35:02 PM

Yes the http://www.vulcandrifterriders.com/clutchspringreplacement.html page are the instructions.

The top 75% of that page are the instructions. The lower 25% was for the Judge's washer install. I have revised the page and made the Judge's washer thing a separate page.

Posted by Bucko
 - August 06, 2015, 11:29:31 AM

Hi Chief:

Did some searching but couldn't find clarity on this...hoping you can offer some advice.

I bought the upgraded clutch spring parts listed in the table here: http://www.vulcandrifterriders.com/clutchparts.html for use in my 01, 1500 Drifter (which just started slipping badly on the weekend).

Do you know if there a description of the install for these upgraded parts, as opposed to the install for the 'Judges' washers option - if there is one -, I can't seem to find it -  or does the install detailed in the following link cover it: http://www.vulcandrifterriders.com/clutchspringreplacement.html

Posted by chief
 - July 31, 2015, 16:01:04 PM
Quote from: jkpq45 on July 31, 2015, 10:25:32 AM

Have manual--don't have access to it per the OP.  Looking through the online version that is stickied at the top of the forum now.

I'll assume the clutch plates are OK and just switch out the friction plates.

You're telling me to "look at the link provided."  This link (http://www.vulcandrifterriders.com/clutchparts.html) says to use 92144-1394 clutch spring for my 1999 1500.  You used the "current" spring (92144-1295).

No, you don't want to use the original spring and holder... you want to UPGRADE  - use the parts listed at the top of that page. The original part has been superseded, so use the newest one. And, you use the TWO holders. This spring and holder combination should resolve the weak spring issue we had on all early 1500's.  The colored chart simply shows the evolution of the spring plate/holders for the 1500.

This page may be of more help. There is a section on Judge's washers... that was an upgrade before KAW re-engineered the spring and holders. Some people like that mod, I didn't think it necessary and didn't do it. Same with using a 2004 MS spring... not needed now, in my opinion.
http://www.vulcandrifterriders.com/clutchspringreplacement.html
You should always measure the clutch package after replacing the friction plates to ensure it is still within specs. Usually it will be, but best to check. If you have to, you replace a steel plate with an undersize or oversize plate depending upon the thickness you got.
Posted by jkpq45
 - July 31, 2015, 10:25:32 AM
Quote from: jkpq45 on July 28, 2015, 08:32:01 AM

I'd look in the Clymer manual but I lent it to my mechanic (cousin) who currently has my Drifter in pieces on the floor of his shop :-)

Have manual--don't have access to it per the OP.  Looking through the online version that is stickied at the top of the forum now.

I'll assume the clutch plates are OK and just switch out the friction plates.

You're telling me to "look at the link provided."  This link (http://www.vulcandrifterriders.com/clutchparts.html) says to use 92144-1394 clutch spring for my 1999 1500.  You used the "current" spring (92144-1295). 

Posted by chief
 - July 31, 2015, 09:54:30 AM

GET A MANUAL!

There is no substitute for a manual. Look at the link provided.
The current spring is what the Kaw engineers are putting in ALL 1500/1600 vulcans... and has been for a while. That is what I have in mine (with updated holders).
You can look up and review the various types of friction plates to determine which is best for you. I used the barnett friction plates and didn't need to change out the steel plates. The friction plates are the same size as far as I remember. The steel plates are all the same size, with one plate used to get the right package thickness... undersize, standard, and oversize.
Again, do yourself a favor and get a manual. They are usually about $40-50.
Posted by jkpq45
 - July 31, 2015, 08:27:59 AM

Are the cork-aluminum friction plates good?  Are fiber ones better?  What is the best?

How many clutch plates of 13089A/B do I need?  One of each?  Which thickness--looks like there are three options?

What about 92145-1243, of which Partzilla says I need 10 ea.?

Posted by chief
 - July 28, 2015, 10:38:53 AM

Personally, I went with the current spring and upgraded to two holders. I replaced the FRICTION plates only. You need to measure the complete package to ensure it is within specs. You have the link to the parts listing and info.

Posted by pcarrell
 - July 28, 2015, 09:13:54 AM

This should answer some of your questions: http://www.vulcandrifterriders.com/clutchspringreplacement.html

Posted by jkpq45
 - July 28, 2015, 08:32:01 AM

Clutch problems with my 1999 1500 Drifter... torn down for fixin'.  Could use your help--comments appreciated.

1.  I see some use clutch spring 92144-1934 (early Mean Streaks), some 92144-1295 (2005+ Mean Streaks).  Is one stronger?

2.  Planning on upgrading to dual holders (13280-1306 and 13280-1307).

3.  I understand there are 8 friction plates (13088)--are the cork-aluminum ones good?  Are fiber ones better?  What is the best?

4.  How many clutch plates of 13089A/B do I need?  One of each?  Which thickness--looks like there are three options?

5.  What about 92145-1243, of which Partzilla says I need 10 ea.?

I'd look in the Clymer manual but I lent it to my mechanic (cousin) who currently has my Drifter in pieces on the floor of his shop :-)

SMF spam blocked by CleanTalk