We limit access by GUESTS to protect our members from spam, hacks and trolls. Please register to gain access to all our resources.
Posted by LarryInSeattle
- August 27, 2015, 03:06:22 AMI tow a trailer with my 800. All led lighting on the trailer. Marker lights removed from the trailer. Blinkers converted to led on the bike. I have spots on the front, but I leave the switch in the off position when towing a trailer.
No additional electrical added to the bike except heated clothing.
Posted by CDNRatMan
- August 26, 2015, 10:48:49 AM 
Ok now after all this soldering instructions, are we any closer to the cause or reason of the wiring failing?
Posted by Brilamb2
- August 26, 2015, 09:40:17 AMI'm a master certified auto mechanic, and from experience if it's an electronic circuit very precise soldering, if it's just power supply then use weather tight crimps. Heat shrink with an epoxy sealant keeps vibration from being an issue and is super secure
Posted by Nanook
- August 20, 2015, 08:20:38 AMI don't have heated grips, my mech was just telling me that he often added heated grips and other heated options on the drifter without any problems, so not to worry, up here we often ride in near freezing temperature 0-5 Celsius. It seems that the bike is not as anemic as we were led to believe. And you got to remember that rarely are all the options and flasher and everything on at the same time.
Posted by chief
- August 19, 2015, 11:44:58 AMThe stock alternator on an 800 Drifter, has a 23.5amp capacity at 8000 rpm... about 329w. At idle you will not have that same capacity. People who simply up the wattage on bulbs in a light bar sometimes have problems with the alternator keeping the battery charged.
It looks to me like you are pushing or exceeding the capacity of the alternator... if the stock bike uses 110w , and your adds are 120w with trailer - you are at about 18a. Your heated grip is about 2.5a. So, you are at 20.5a. I don't know what else you have running.I bought a new trailer once and had a hitch and wiring professionally added to my van. With the trailer hooked up I'd end up blowing a breaker in the brake lighting system. I bought a bike trailer and no problems. Apparently something in the other trailer was not wired correctly.
Posted by Nanook
- August 19, 2015, 10:09:12 AMWell, I talked to my mechanic this morning. He told me that The genrator is good for 350 watts on a drifter 800 wich is just under 30 amps and that the bike stock, uses about 110 watts. So we have 240 watts free, roughly 20 amps. So he's shure that I haven't overload the system, even with the trailer, since all my adds on on the bike is under 80 watts, and the trailer is under 40 watts. He told me that he installed heated grip, and plug for heated garment without any problem by limiting other add-on.
Posted by greenbarn
- August 18, 2015, 21:55:47 PMI've barely been able to keep up on this thread, but thought I'd weigh in on this. Nanook, to have such a catastrophic problem (melted wiring), like others have said, sounds like you had a short to ground on your harness- could just be a really small spot rubbed on a wire - these are hard to find. Hard shorts to ground sometimes do weird things, they are so instantaneous. The fuse SHOULD blow, sure, but who knows.
As far as solder vs. crimp: this is complicated. There are varying degrees of "soldering" (based on the skill of the "solderer" ) and CERTAINLY varying degrees / qualities of crimp connectors. I'd say soldering is preferred if 1) you have been factory-trained in soldering or are very good at soldering and 2) you have plenty of time, or don't have many connections to make. Otherwise: if you use GOOD QUALITY heat-shrink crimp connectors - AND you crimp correctly --- I'd tend to lean towards the crimping method. I run an auto repair shop - we probably use a couple hundred crimp connectors a year - and have never had a come-back for bad connectors. Yes, I have fixed hundreds of poor crimp connectors, but if you do it right and use quality connectors it works real well. And crimp connectors take about 1/10 the time as soldering. I'm in the process of doing custom lights on my 800, and I have about 50 connections - I'm using heat shrink crimp connectors - about 15 seconds per connection vs. much longer for soldering. Either way you do it, you have to do it right. If you are really good at soldering this might be just the thing. If you are not, there is much greater risk of bad joints, IMO, than crimp connectors. But, then, you have to do the crimp connectors right, too. It's much easier to learn to crimp than to solder.
I buy good quality heat shrink connectors, and have a good quality crimper - it doesn't have to be a $100 crimper, but has to crimp well without pinching the insulation in half. Got any "scotchlock" connectors that you just pinch together and they pierce the insulation and connect the wires? Throw them away, they're junk. The scotchlocks with the gel in them are OK, but not as durable as a good heat-shrink connector. I buy mine from Terminal Supply, but I'm sure there are others that are OK. Likewise, the cheap vinyl (non-shrink) connectors - they're OK, maybe, for under the dash of your old truck, but leave them off your bike.
One last thought.. for what it's worth, if you notice almost all of the factory connectors, auto or motorcycle, are crimp-type connectors.
Posted by chief
- August 18, 2015, 12:41:28 PMOkay all you tech wizards... how about doing a video and/or write-up on:
1) proper solderingand
2) proper crimping
I may be able to find some online, but would rather have a Drifter rider do it!
Posted by Troll
- August 18, 2015, 10:05:48 AMThe reasons you state are valid, but they really only apply to those joints that are TOO BIG. You want to make the connections as small as possible and NEVER have several in a row, they should all be staggered. The absolute best repair has a wire joiner soldered and sealed at the point of the repair. We spent quite a bit of time at the G.M. Special Electronics School I went to learning how to solder and seal connections and do it so there was zero resistance and possibility of atmospheric intrusion (Weather-Pac connectors). Most people just blob it on...that's not how it's supposed to be done.
Posted by Nanook
- August 18, 2015, 08:46:18 AMThe main argument against solder joint by professional is that when you solder a multi strand wire, it basically become a solid strand wire, wich might be ok in home electricity but is really not recommended in a vehicule with the vibration. When it breaks it will break completely, but keep touching making intermittent connection wich is a real nightmare! That is why all harness wiring is done in multi-strand.
Posted by Troll
- August 18, 2015, 08:14:13 AMSolder and seal with heat shrink. You can use a 25 watt iron and electronic solder. It has a low melting point, and does the job without overheating the insulation nearby.
Posted by 49Reo
- August 17, 2015, 23:50:10 PMI use a product called "Liquid electrical tape" it is a black gooey mixture that I put on soldered connection, then slide shrink tube over and heat it up; it oozes out as tube shrinks, making a water proof connection. Over the years I have done a lot of vehicle wiring and had repair a lot of other peoples wiring, the only problems I have ever had on connections are those done with crimp connections with the exception of one: my son bought a used Jeep TJ, it had an issue with the main wire from the alternator; I undid the connection to find that someone (PO) had twisted the wires together and used seal-all and tape; never had a soldered joint that was sealed corrode. But, each to their own... I always pack some stakons and crimping pliers for road side fixes, but always redo them when I get home.
Posted by Nanook
- August 17, 2015, 20:31:58 PMQuote from: 49Reo on August 17, 2015, 19:37:05 PMDid you use crimp connectors or solder and shrink tube? Crimps are okay for a roadside fix, but tend to corrode over time which causes nothing but trouble.
This is another big debate. Many proffesionnal claim that crimping is the best way to do it and that solder is the least reliable. But to accomplish this reliability you need high end crimping tool, and good connector. Before I got a good crimping tool i relied mainly on solder but got a few problem with it. Now I mainly crimped and sometime use just a tiny bit of solder. Shrink tube again is a must, good thick one.
Rob
Posted by 49Reo
- August 17, 2015, 19:37:05 PMDid you use crimp connectors or solder and shrink tube? Crimps are okay for a roadside fix, but tend to corrode over time which causes nothing but trouble.
Posted by Troll
- August 17, 2015, 19:36:42 PMThe service manual rates the alt. at 23.5 A. Not a whole lot, but all you really have to run is the headlight, taillight, and the ign system. A 1500 has the electronics and fuel pump to run, so that wouldn't be nearly enough. They don't break down the electrical load by user, so the best thing you can do is keep your use to a minimum.