Modify message

The message has the following error or errors that must be corrected before continuing:
Warning: this topic has not been posted in for at least 180 days.
Unless you're sure you want to reply, please consider starting a new topic.
Attachments: (Clear attachments)
Restrictions: 6 per post (6 remaining), maximum total size 64.00 MB, maximum individual size 29.30 MB
Uncheck the attachments you no longer want attached
Click or drag files here to attach them.
(Clear attachments)
Other options
Shortcuts: ALT+S post or ALT+P preview

Topic summary

Posted by Troll
 - January 20, 2014, 14:02:41 PM

Never saw one with a 90 deg. bend before, only straight. Rat, as in Ratman...swing arm on his 800

Posted by CDNRatMan
 - January 20, 2014, 13:15:34 PM

   I never did find a size so I just took the tie rod in with me and Pauline just found the right one for me, one that was metric, the part number is  49001-0001. None of the fiche sites had a size that I found.

Posted by Drift1
 - January 20, 2014, 13:05:18 PM

hey rat what is the size for these ? I'm almost done  getting the front buttoned up and going to be moving on to the next section .

Posted by CDNRatMan
 - January 20, 2014, 12:44:36 PM

  everything is good went back to CARQUEST and I have the correct size and thread count, same as what Kaw sells and they were like $1.99 ea so replaced the ruined one and have 2 spares in my spare parts box.

Posted by Bucko
 - January 20, 2014, 12:21:48 PM
Quote from: Troll on January 18, 2014, 09:09:29 AM

This is the kind of fitting I have on my u-joint, inside the swing arm. There is no problem getting to it, as I drilled a 3/8" hole in the swing arm bell and plugged it with a black plastic cap..Using these on Rat's swing arm might pose a problem, though, since the needles used to inject the grease are about 3" long, and do NOT bend around corners..90 deg fittings would be easier to get at, but they hang down too low, and since he already destroyed a short fitting, the long ones would be more prone to disaster!

Hey Troll:

Not sure of the exact application you're referring to as I"m not familiar with 'Rat's swing arm' but they do make those blunt nose grease needles with a 90 degree bend in the end if that would help.  I had to pick up one of those bent needles to get at the lower ball joint grease nipples in my Jeep - the U Joint barely clears the button grease fitting but by rotating the U joint, I can just get one of those bent needles between the fingers of the u-joint to reach the fitting.

Posted by CDNRatMan
 - January 18, 2014, 11:46:26 AM

    Bucko and Troll first, the nipples and the ground do not leave a lot of room to move around in, you would need a short nipple and a flexible hose to get on it.
49 this was most likely caused by a rock strike or something similar, or going up over a curb, I have never heard the nipple strike anything since I owned the machine, not saying I did not do the damage. and they are in a line and the center one just hangs a tad lower.

GB, wait till I talk to the missus about you......it will be more then the doghouse you will be in.......lol....

Have three new ones on order and will replace them once I have them here.

Thanks for all the concern over my nipples....... ::) :o

Posted by greenbarn
 - January 18, 2014, 09:23:45 AM

...Or he could just quit dragging his nipples...    Just a thought ;D

Posted by 49Reo
 - January 18, 2014, 09:13:29 AM

Not being familiar with the 800's, is there any way to drill and tap in a different location where it wouldn't get hit so easily, then put a plug in the existing hole? Just a thought.

Posted by Troll
 - January 18, 2014, 09:09:29 AM

This is the kind of fitting I have on my u-joint, inside the swing arm. There is no problem getting to it, as I drilled a 3/8" hole in the swing arm bell and plugged it with a black plastic cap..Using these on Rat's swing arm might pose a problem, though, since the needles used to inject the grease are about 3" long, and do NOT bend around corners..90 deg fittings would be easier to get at, but they hang down too low, and since he already destroyed a short fitting, the long ones would be more prone to disaster!

Posted by Bucko
 - January 18, 2014, 00:00:09 AM

You can also use a 'button' style grease fitting.  You'll need a 'needle' type injector (not the really pointy one).  The advantage is they're very low profile.

Posted by aralph
 - January 17, 2014, 17:58:50 PM

with all that cold weather your having up there I would expect your nipples to be hard  :-[

Posted by 49Reo
 - January 17, 2014, 17:12:01 PM

I was afraid to open this with that title!!

Posted by CDNRatMan
 - January 16, 2014, 20:03:08 PM

  If you notice I just asked a simple question and they took it off the rails.

the thread would also be metric Troll

D1 I have been taking pictures and making notes so when I post it it will be easy as pie to do it and follow along....

oh are is a picture of my nipples...there was fresh grease in there but not sure if it was enough and remember last fall it was hard but not impossible to pump the grease in so it might have been hit with a rock while riding during the summer, so for the cost of the three I'll just swap them out.......

now if I owned my own tire place I know I would have some in stock for my Drifter buddies.........

Posted by Troll
 - January 16, 2014, 19:35:32 PM

This thread is getting kinda scary!

Posted by Drift1
 - January 16, 2014, 19:31:33 PM

I hope your jotting all this nipple thing going on for the mod section so others know how to replace the rear shock and whether to get big , small , pierced , tattooed or what ever else your doing to the rear end of this bike  ::) ;D ;)

SMF spam blocked by CleanTalk