We limit access by GUESTS to protect our members from spam, hacks and trolls. Please register to gain access to all our resources.


The plugs.
Can a compression test be done incorrectly?
Sounds like the automatic compression release isn't working...manual says 50-85 psi...assuming the compression release is operating correctly. I really don't think that the compression pressures you have point to a problem with oil consumption. What do the plugs look like? Are there deposits on the electrodes? What color are the insulators...
I did a compression test today and this is the psi.
Front cylinder 149 dry, 165 wet
Rear cylinder 125 dry, 140 wet
What would happen if you overfilled it?
41.5 is pretty good, I should think. Mine was getting around 37-40 before I started tinkering with it. Did you ever get the oil screen out ? No point in trying to dyno tune an engine without the box, since that's where they are going to be fiddling with the fuel curve....Keep an eye on the oil usage, maybe the additive package in the amzoil didn't get alone with what was in there before...It's just me, but I check my oil at least once a week. I use a mechanic's mirror so I can sit on the bike and hold it straight and look at the eye...sure wish it had a dip stick.
Quote from: Troll on September 17, 2013, 17:59:58 PM19k on the clock.How many miles on this engine? Something doesn't sound right. Have you been using the amzoil right along, or is this something new? I have seen car engines with lots of miles suddenly turn all the ring end gaps so they line up...for no apparent reason. Ring seal doesn't seem to be a problem with these engines. You are running rich, what happened to your fuel mileage? Is it sudden? Vacuum leaks at the MAP sensor and a leaking fuel pressure regulator, or even a stuck open injector could do this
I called three techs today and they all told me I needed a power commander in order for them to dyno tune the bike. I thought aftermarket pipes and a aftermarket air filter would cause the bike to run lean? Would hotter plugs fix or put a band aid over the problem? I mean just to see If I need it dyno'd?
How many miles on this engine? Something doesn't sound right. Have you been using the amzoil right along, or is this something new? I have seen car engines with lots of miles suddenly turn all the ring end gaps so they line up...for no apparent reason. Ring seal doesn't seem to be a problem with these engines. You are running rich, what happened to your fuel mileage? Is it sudden? Vacuum leaks at the MAP sensor and a leaking fuel pressure regulator, or even a stuck open injector could do this
Troll, I am smoking on acceleration and smell of gasoline. It's a black smoke. My plugs are also very dark after 5k and smell of gas.
I just noticed my oil is low too today. I just did an oil change with Mobile 1 a little while back. I need to get that stuff outta there.
Quote from: Petemoss on September 16, 2013, 20:37:57 PMFor what?
Question. If the bike is running rich, gasoline will dilute the oil. Will the diluted oil pass through the rings and burn out of the tail pipe? Would a tune up fix this problem?
LEAKS.....you might not notice it because of where it is. What kind of oil did you run 5,000 miles?
Quote from: Troll on September 16, 2013, 15:57:22 PMFor what?...Check the vapor drain on the front of the engine, right ahead of the front cylinder. It has a pretty cheesy clamp on it.
Question. If the bike is running rich, gasoline will dilute the oil. Will the diluted oil pass through the rings and burn out of the tail pipe? Would a tune up fix this problem?
The spark plugs have 5k roughly on them and they are dark and smell like gas.
John, the Drifters don't have a pog. The trick now is to find out under what circumstances the oil is being used. I have 81,000 on mine and it has 0 oil consumption...You will need someone to follow you and determine if the engine is smoking on acceleration or on decel...Generally, worn rings will cause smoke under power, and valve guides/seals on decel...Check the vapor drain on the front of the engine, right ahead of the front cylinder. It has a pretty cheesy clamp on it.
That sounds as if your oil pump is not working, I thought all the drifters had the POG plastic oil gear replaced but if you have only been doing short runs then just maybe you have got away without doing too much damage if the pump is not working...You should take the bike to a kawasaki shop and ask them to do an oil pressure check..If the pump is not working you are looking at a very expensive repair including total removal of the engine. You can buy a 'Judges' steel gear and a kit with instructions to fit it but expect to pay over $200 for it and if you follow the instructions carefully it might be possible to do the work in about three hours..
John.
Quote from: 49Reo on September 14, 2013, 23:31:00 PMThe only smoke I have noticed is the black soot that seems to more or less "spray" out of my pipes. On startup, on up shift. My plugs are new (5k) and very dark and smell of gas. I thought I was running a tad rich. Would running a rich cause that much oil usage? I have 19k on the clock.The K&N filter oil is red; likely source. Has your bike been smoking? That's a lot of oil; mine uses none.
Page created in 0.057 seconds with 12 queries.