We limit access by GUESTS to protect our members from spam, hacks and trolls. Please register to gain access to all our resources.
Posted by Troll
- September 26, 2013, 09:16:46 AMOK, MAK...here's the link: http://www.vulcandrifterriders.com/forum/index.php?topic=9911.msg34043#msg34043
The joint was for a 4 wheel atv, and costs less than $30.
Posted by Mak
- September 26, 2013, 08:15:21 AMTroll
Can you help me finding your write up on the u joint pls? Thanks
Mak
Posted by Mak
- September 26, 2013, 08:13:53 AMI have done it - and its worth it too. I am doing things like that on all 3 of mine and the inside looks like just out of the factory, well almost lol. In fact I grease up every "hollow" part I can that inc's also the fork covers and I use PLENTY of WD40 spraying it into the swingarm bridge ...
I am just completing my MakMachine that stood for a few years and endured shipping from the middle east to London and then from there to OZ. The preparation I did proved totally worthwhile, not a single deterioration anywhere ...
If you encounter fly rust - use WD40, a drill with low / vari speed, a long cheap drill bit or other steel rod, fine steel wool (you can use the steelo for the dishes too) and in low speed give it a "polish", but keep using plenty of WD40. Then grease up with a layer or General automotive grease.
Mak
Posted by capnconch
- September 25, 2013, 06:25:50 AMQuote from: DC on September 24, 2013, 10:58:01 AMPer owners manual the scheduled propeller shaft maintenance service is every 12,000 miles, also time to lube the swingarm pivot.Is 17k a hard number or is it dependent on riding conditions?
Posted by DC
- September 24, 2013, 10:58:01 AMIs 17k a hard number or is it dependent on riding conditions?
Posted by capnconch
- September 24, 2013, 09:32:48 AMMaybe I should rephrase and modify my question; Who actually has had this service done either by themselves or at the dealer or cycle shop?
Am I the only negligent owner here?BTW, I'm not really negligent in all other areas of my Drifters maintenance just in this particular area, and no I haven't tackled the job yet. Daily Monsoon rains continue here in SW Florida so I haven't been riding either.
Posted by Troll
- September 20, 2013, 15:24:23 PMI have, and I replaced my U-Joint, too. I have lubed my swing arm bearings, greased the drive spline where it goes into the rear wheel...lots of stuff. Just takes time, it's not rocket surgery, just nuts and bolts. The hardest part of this whole thing is getting the bike so it's stable enough to do the work with the rear wheel off the ground. I did a write up on replacing the bevel drive housing last month...again, no big deal. I believe it's posted under mods and tips....
Posted by capnconch
- September 20, 2013, 10:27:41 AMI just flipped 17,000 mi on my Drifter 1500 and I have read Gadget's Lube your driveshaft instructions for years. I refuse to go to dealer to do this but I keep putting it off.
How many of you out there have actually done this procedure?
Or do you really trust your dealer or bike shop to do it and hope they do it right.
I AM GOING TO DO IT!. To Harbor Freight today to get the circlip pliers, time to get down and dirty.
But who else has done it themselves..Show of hands please and if you don't mind, tell of any obstacles you may have encountered.
I successfully lowered my front fork springs 1 " Progressive springs, without removing the forks!!! (bent wire coat hanger to fish out the stock springs and stuff out.) Will write an article on this shortly.
Conch