GUEST? Registration opens up many more resources which are not available to guests. Registration is free, we never sell or give others access to your information.
Posted by darkdrifter
- May 02, 2013, 20:10:41 PMthanks for the reply, troll!
I see you own a harley also. its nice to see another motorcycle rider that is above the "american vs metric" snob bs. I've never owned a harley, but owned a 01 indian and now my 2010 darkhorse, and theres no comparison in the craftmenship of a drifter vs modern Indians, overall. the gilroy era, kings mountain era, and now even the spirit lake (polaris) era indians are all sporting lots of over-seas parts.
I wish all the parts on my 2010 indian where american made, the parts that aren't, I wish where from japan. my experiance with japanese quality stuff vs, all the other asian manufacture, is a night and day differance.
I just did a bing image search on the nomads and I'm only seeing them with rectangle shaped master cylinders.
my girls 800 drifter resides most the time in my garage next to my Indian, so I figure I'll first do what you suggest and just put the drifter brake mc and see what happens and go from there. the banjo fittings are the same.
I would guess my more complicated obstacle would be if I needed more flow capacity since I'm going from single to dual, then my bore would need to be increased?
if it needs to be the opposite, I could plumb in a restrictor.
I didn't even think about the lever travel.
and now you've got me nervous about the clutch side, lol!
since her 800 doesn't have hydraulic clutch, I'd have to pick one up used on the cheap and give it a whirl.
it might be alot of work just because I like the looks of "round" vs "rectangle".
but hey......I've never been accused of being a rational or intelligent thinker 
Posted by Troll
- May 02, 2013, 15:19:50 PMThe Nomad has dual calipers, but it's not just a matter of that. Lever ratio and total swept area of the cylinder must be kept in mind. When I went to a newer model M/cyl on my FLT, it went from a 1/2" bore to 3/4" bore, and the lever travel DECREASED by about 50%, but the lever pressure increased, but not by the same amount. The effective pressure at the calipers increased, and the brake performance improved. I put 11/16" bore cylinder on my SuperGlide, to go with the dual caliper setup I put on that, and the performance improvement was quite startling. Lever travel was slightly more than the FLT (same calipers/discs), but the feel and feedback was improved. The Sglide weighs about 300 lbs less, and I was able to get it to stop from 60 mph in 100', quite consistently, there was no brake fade even after many stops. Bottom line: putting a different M/cyl on might improve braking, or it might cause a nightmare..experimentation is the only way to find out. As far as the clutch is concerned, I'm thinking that it might not be as simple as you think, for the same reasons as the brake, clutch piston travel and lever ratio will be important here, too. Then there is the problem of the banjo fitting......
Posted by darkdrifter
- May 02, 2013, 14:59:04 PMthats the info I need.
many many thanks, pilgrim!
I am actually debating picking up a set for my 2010 Indian. It came factory with the hydraulic clutch, but the master cylinders for the clutch and the brake are rectangular shaped, wheres as the drifters\vulcans are round. the round looks way better.
It has 1 inch bars, so that would not be a problem.
the clutch side should be a easy swap. but the front brake would be a problem since I have dual calipers on the front. So I'm assuming the piston size will be differant.
Does anyone have any experiance using the factory drifter brake master cylinder and converting to dual calipers on the front?
Posted by Pilgrim
- April 27, 2013, 14:02:53 PMIt is a single pole double throw (SPDT) switch- when the handle is released the wires black to black/red are made.
When handle is pulled in the wires black to black/yellow are made.
black is the common.
If the connector comes loose, the bike won't start. Found that out yesterday after installing risers.
Posted by darkdrifter
- April 26, 2013, 21:52:57 PMconcerning the clutch switch on the LH lever,
would anyone happen to know if the circuit becomes open, or closed, when you pull the clutch lever?
thanks in advance for any help.