We limit access by GUESTS to protect our members from spam, hacks and trolls. Please register to gain access to all our resources.
Posted by Troll
- September 11, 2012, 07:59:57 AMPosted by Troll
- September 11, 2012, 07:58:07 AMThe factory preload spacer is a piece of exhaust tubing, cut to length. Progressive usually packs a pair of PVC pipes in the kit for you to cut to length...standard operating procedure
Posted by greenbarn
- September 10, 2012, 21:37:01 PMQuote from: Troll on September 10, 2012, 14:10:56 PMThat's a great link - I spent a bunch of time reading a lot of different articles - but I can't find the one you mentioned on adjusting preload... What's the title? I searched for "preload", "pre-load" , "load", and can't find anything....Go here first and check out how to check and adjust preload.
http://www.gadgetjq.com/gadgetsfixitpage.htm
And, Troll, what do you think of the sugestion in the article in afore-mentioned gadgetsfixitpage, that talks about adding a 4" piece of PVC on top of each shock spring, in order to increase the preload?? (article "install progressive springs...") http://www.gadgetjq.com/installprogressivesprings.htm
Posted by Troll
- September 10, 2012, 14:10:56 PMThere are a few things to do first, like adjusting the bearing preload. The neck bearings should be repacked every 10,000 miles, but it's an easy, but time consuming job. Replacing them is about $40 in parts and labor...
Go here first and check out how to check and adjust preload.
http://www.gadgetjq.com/gadgetsfixitpage.htm
Posted by chief
- September 10, 2012, 10:33:41 AMTIRE PRESSURES:
See Mods/Tips... for this topic.http://www.vulcandrifterriders.com/forum/index.php?topic=17347.0
Posted by mbk
- September 10, 2012, 09:37:24 AMThanks so much - if it's the worst-case scenario like that with the bearings, is that an expensive fix? Sounds like it.
Posted by Troll
- September 10, 2012, 08:42:14 AMThe front end is a critical part of any motorcycle. I would suggest that you raise the front wheel off the ground and check for any looseness in the steering head bearings. My 1500 now has 71,000 miles on it and when I got it, the small, sharp edged bumps really transmitted up to the bars. The dealer told me that it was worn slider bushings...I kind of doubted that, since I had never had to replace slider bushings in anything I owned for the last 50 years, so that Winter I disassembled the fork, replaced the springs with progressive wound ones, adjusted the preload to my liking, and replaced the fork oil with Dexron 3 synthetic ATF...problem solved. You might also check the front tire pressures...for some odd reason, people have been running way too high a pressure in tires lately.. My 1500 manual calls for 28 psi cold in the front, and that's just fine...
Posted by mbk
- September 10, 2012, 08:29:51 AMI posted elsewhere about getting my "new-to-me" 2004 Drifter 800, but I wanted to ask specifically about the front suspension issue I mentioned in that post. When I hit some bumps in the asphalt on my back-roads ride home -- the bumps were kind of like little mini speed bumps but not nearly as high-more like some faults in the rode where the asphalt kind of rippled upwards like folds in a sheet -- I noticed that I could really feel that front fork not just compress, but could feel slight slop/movement in the fork tube. The bike is in excellent shape otherwise and only has 4,000 miles on it (a 2004) so is this just a real soft front suspension or something I should be concerned with? Mike