We limit access by GUESTS to protect our members from spam, hacks and trolls. Please register to gain access to all our resources.
Posted by lumper
- June 12, 2011, 20:01:37 PMOk, great I will look for you too.
Got the stud out, whew!
That wasn't pleasant.
I used a dremel and friend and we cut a groove into it and I bought a big screwdriver at H. depot and eventually we got it out with a 12" crescent wrench on the screwdriver and some steady pressure.
I Am so glad I was able to fix it in the 11th hour, we are planning on leaving around 10 am tomorrow so this was my last chance before our trip to try to get it.
Hope to see some of you folks on the Road we will be all over the state and into Maine too.
Lump
Posted by TheBreeze
- June 12, 2011, 18:10:03 PMI plan to be in Laconia at least a couple of times this week. My Drifter and I will be all over the state and will keep an eye out.
Posted by Troll
- June 12, 2011, 08:47:13 AMI have left hand drills just for this task. Most of the time, the stud spins out while you are drilling....
Posted by Varooom
- June 12, 2011, 07:51:55 AMlumper,
I may be up mid week and will look for Lime!
Re your broken stud, if there's room, take the Dremel tool and grind the face as flat as you can. Then, grind a drill bit so that it's cutting edge is backwards; so that it cuts material when the drill is in reverse.
Heat up the stud a bit with a torch.
Apply some silicone or other penetrating lube.
Using a ball-peen or other hammer, bang a center point hole in the stud; this will help the lube penetrate too, hopefully, and hold your bit in the center as you start.
Set your drill on reverse and have at it.
I've seen machinists use this method. You'll be drilling and (using a bit that's smaller than the thread diameter to preserve the threads in case you go below the surface in trying to drill it out) it will hopefully spin out during the process.
Clean out the threads and Bob's your Uncle.
Varooom
Posted by lumper
- June 11, 2011, 18:59:29 PMTroll,
No, I tried both the metric and english extractor kits, none would grab the stud enough to get anywhere near a turn.
There is I guess 3/8" sticking out and I think a 7mm would grab it.
The 6mm is to small and the 8mm a hair to big, there wasnt a 7mm extractor in the kit so for now I dont know what to do.
A friend wants to use a dremel and cut a groove for a screw driver and try using a chord less drill, but I dont know.
I have been driving it like this here and there since I haven't been able to fix it.
Varoom,
I didn't see any Drifters the last time IJ was there, I hope to find some though.
Depending on the weather I plan on being at Weirs beach on Weds and Sunday otherwise weather permitting we are going to be in the north playing around.
If you happen to be around on those days look for my Mint green 99 Drifter, no Chrome.
Posted by Varooom
- June 11, 2011, 16:20:58 PMYou will see Drifters in Laconia and Weirs Beach and all over. I'd be up there now if it weren't raining for the next four days. Hopefully it'll abate and I can run up on my new 2005 two tone black/grey 1500.
Varooom
Posted by Troll
- June 11, 2011, 07:47:19 AMDoes this mean you have your stud problem fixed? 
Posted by lumper
- June 10, 2011, 22:21:35 PMJust wondering if any of my fellow Drifter riders are going to be around Laconia during bike week.
I haven't ever seen another Drifter on the road and thought it would be cool to meet some northeast Drifter riders if you are planning on going.
My wife and I are going to be a few miles north of Laconia in Campton, NH from Weds thru Sunday.
We plan to ride to some white Mt events and check out the drive in for vender deals and cool bikes on one or two of those days
If anyone wants to meet up somewhere speak up.
Lump