GUEST? Registration opens up many more resources which are not available to guests. Registration is free, we never sell or give others access to your information.
Posted by Fab
- July 27, 2025, 16:02:59 PMQuote from: moto on September 19, 2018, 13:14:26 PMhere is a video what I done:
and I am verry happy of that sound, this is enough for me and my wife
Moi Jari 
I know this is an old post, but I was wondering if you still have the video of your OEM exhaust with the silencer removed.
The link in your post no longer works.
Kiitoksia!
Posted by moto
- September 20, 2018, 06:42:26 AMQuote from: mittico68 on September 20, 2018, 05:28:37 AMThanks!!Well done.
And nice bike, too!
Posted by mittico68
- September 20, 2018, 05:28:37 AMWell done.
And nice bike, too!
Posted by moto
- September 19, 2018, 23:27:46 PMQuote from: drifter-paul on September 19, 2018, 19:36:06 PMThanks Paul!Lovely job, Moto. Sounds good and I love the knee tank gaurds.
Posted by drifter-paul
- September 19, 2018, 19:36:06 PMLovely job, Moto. Sounds good and I love the knee tank gaurds.
Posted by moto
- September 19, 2018, 13:14:26 PMhere is a video what I done:
and I am verry happy of that sound, this is enough for me and my wife 
Posted by drifter-paul
- September 19, 2018, 03:11:01 AMYeah, coming back to me now, it was 7 tears ago I removed the exhaust and then replaced it. From memory I put a wooden stick down from the engine side and gave it a few thumps, there was only 1 tab weld holding that plate in place, after that, the whole thing was then just an empty tube.
Posted by moto
- September 18, 2018, 11:33:38 AMIt's done. Now this muffler is real empty, two baffles are taken off, this is last one at first picture.
Posted by moto
- September 17, 2018, 05:34:10 AMQuote from: drifter-paul on September 17, 2018, 04:58:36 AMThis exhaust is OEM, default factory exhaust. In this photo, I am removed my fishtail tip so I can reach better to remove these two baffles out.
My oem was a 'fishtail' , oval shaped at the end with 2 or 3 small pipes projecting out. Held by 1 screw with no internal baffling - very effective in muting the sound.
This was an Australian model, but I don't think we're talking OEM, here..
Posted by drifter-paul
- September 17, 2018, 04:58:36 AM 
My oem was a 'fishtail' , oval shaped at the end with 2 or 3 small pipes projecting out. Held by 1 screw with no internal baffling - very effective in muting the sound.
This was an Australian model, but I don't think we're talking OEM, here..
Posted by moto
- September 16, 2018, 13:50:20 PMOk, here is the second baffle what I must to take off. I starting to drill first 6mm holes around these two inner pipes and 4mm drill I make those two tight sides. Before chisel second baffle I must to lower this one aligment plate edges so that is not blocking the baffle
when I taking it off. I am not very sure, if this plate edges blocking that baffle that baffle can fit this hole.
Posted by moto
- September 13, 2018, 10:43:50 AMWell , maybe I try to remove the second baffle out. It is the similar like first one what I took off.
The second is more deeper inside muffler and I need long drill and chisel.
If anyone has informations, is this second connected like first one, let my know, thanks.
I put pics over there when I start this second round!
Posted by moto
- April 28, 2018, 14:38:41 PMYes, sound is good. Not too loud but perfect. I dont want to hear so loud like V&H pipes is.
Posted by AZCaveman
- April 11, 2018, 15:08:35 PMWithout removing the goat bladder, I doubt you
will notice any real difference.
Posted by moto
- April 05, 2018, 23:21:57 PMQuote from: Old Drifter on April 05, 2018, 20:22:01 PMI don't test yetGlad to hear that it worked out. How does it sound with the pipes removed?