GUEST? Registration opens up many more resources which are not available to guests. Registration is free, we never sell or give others access to your information.
Posted by Troll
- May 03, 2025, 16:06:21 PMMight seem an odd question, but....does this thing have a programmer on it? None of this makes any sense, unless there is a problem with the controller. Just another thought, because I can't see the bike: You wires the coils correctly? The twin plug system DOES NOT control one cylinder per coil, but rather one front and one rear. It should run on one coil, as long as it's splitting the spark between the cylinders. Decades ago, I dual plugged my 98 inch SuperGlide. Initially, I used two coils, one for the right side and one for the left. I replaced the ignition controller with a "single fire" system with 2 pickup coils. That let me run one coil for the rear cylinder, and one for the front. That allowed me to set the ign. timing separately for each cylinder, and use the full voltage from the coils to fire the plugs. The Drifter does not have a single fire system.
Posted by Dustywolf
- May 03, 2025, 00:32:27 AMQuote from: chief on May 02, 2025, 16:10:09 PMECU test results?
No codes.
Posted by chief
- May 02, 2025, 16:10:09 PMECU test results?
Posted by Dustywolf
- May 02, 2025, 01:44:51 AMYep, so everything's working, bikes cranking great.. but it's still spraying too much fuel for the bike to start. Plugs are still dripping wet... we followed the vacuum diagram.
It feels like every time we fix one issue, another one comes right around the corner.
Posted by Bucko
- April 29, 2025, 18:06:39 PMIIRC, there's one in the first fiew pages of the service manual.
Posted by Dustywolf
- April 29, 2025, 05:02:28 AMGood news, we have spark but now no fuel spray.
Does anyone have a vaccuum hose diagram? Of so, please post it here.
Thanks!
Posted by Dustywolf
- April 21, 2025, 01:11:59 AMSo, good and bad news.
Map sensor vaccuum wasn't hooked up at all, got all new vaccuum lining and that fixed the fuel problem for the most part.
Now, I no longer have any spark. This is bizzare. Went from having strong consistent spark to none.
Will add, anytime I apply slight throttle while cranking it, the starter relay will click.
Anyone have any new ideas?
Posted by Dustywolf
- April 18, 2025, 14:38:11 PMQuote from: Troll on April 18, 2025, 14:17:02 PMFuel pressure regulator works to reduce the line pressure only after the engine starts. It's vacuum controlled. Stuck injectors spray fuel as soon as they have pressure applied to them Injector pulse width is controlled by the fuel map in the ecm, and the cell addresses vary by the coolant temperature reading.
Makes me think it has to do with my throttle position sensor... I'll test that according to manual specs
Posted by Troll
- April 18, 2025, 14:17:02 PMFuel pressure regulator works to reduce the line pressure only after the engine starts. It's vacuum controlled. Stuck injectors spray fuel as soon as they have pressure applied to them Injector pulse width is controlled by the fuel map in the ecm, and the cell addresses vary by the coolant temperature reading.
Posted by Dustywolf
- April 18, 2025, 00:04:06 AMUpdate: still figuring out the injector issue.
They do not appear to be leaky or stuck open, but when I try to start the bike they fire an unreasonable amount of gas. And there is a lot of pressure in the return line to the tank, could it be the pressure regulator?
Posted by Dustywolf
- April 16, 2025, 11:38:49 AMSo, I suppose I did a combination of things and now I have strong consistent spark.
Now, everytime I try and start it it'll gunshot or pop but won't full on start. I can see fuel mist leaving the pipes.
Plugs end up dripping wet, what do I do now?
Maybe my injectors are stuck open? Sure seems like it
Posted by Dustywolf
- April 15, 2025, 02:13:50 AMQuote from: 53Indian on April 14, 2025, 18:29:31 PMI'm sure you've tried this, but did the ecu fault code flash anything up?
Only in the past, and it was the fuel pump which I ended up replacing.
Posted by 53Indian
- April 14, 2025, 18:29:31 PMI'm sure you've tried this, but did the ecu fault code flash anything up?
Posted by Dustywolf
- April 10, 2025, 13:06:49 PMQuote from: Bucko on April 10, 2025, 12:54:01 PMJust thinking outside the box.... assuming you have the plugs contacting cylinders, maybe they spark once when you hit the starter but then due to the cranking vibration they lose contact and don't spark?
Good thought, but I have my buddy holding up the bike and pulling in clutch and holding the start button for me. I'm definitely making contact so that isn't it.
Such a weird issue.
Posted by Bucko
- April 10, 2025, 12:54:01 PMQuote from: Dustywolf on April 09, 2025, 23:53:53 PMI'd think that's part of my issue (having all the plugs out, or 2 at a time out) but that still does not really explain why it only sparks ONCE when I press the starter button.
It makes me think something is telling the ECU "hey, shut off spark."
Just thinking outside the box.... assuming you have the plugs contacting cylinders, maybe they spark once when you hit the starter but then due to the cranking vibration they lose contact and don't spark?