Modify message

The message has the following error or errors that must be corrected before continuing:
Warning: this topic has not been posted in for at least 180 days.
Unless you're sure you want to reply, please consider starting a new topic.
Attachments: (Clear attachments)
Restrictions: 6 per post (6 remaining), maximum total size 64.00 MB, maximum individual size 29.30 MB
Uncheck the attachments you no longer want attached
Click or drag files here to attach them.
Other options
Shortcuts: ALT+S post or ALT+P preview

Topic summary

Posted by rob f
 - May 01, 2018, 08:19:39 AM

Drained and filled mine with no issues.
May want to consider changing the thermostat while it is all drained.
Didn't change mine because of the low mileage and would have cost more money.
Looks like we all ride the "Cheaper is better " wagon.
After all, if cost was not an issue we would all be riding "real" Indians.
Am I right?
R

Posted by CDNRatMan
 - April 30, 2018, 23:49:51 PM

 ;) Stroker after you have finished beating yourself up over your being cheap, then take a very deep breath and laugh out loud because I am sure we all have fallen prey to the same issue........

Posted by Stroker Deuce
 - April 30, 2018, 23:08:10 PM

Thanks for the replies.  I received the fan switch ordered from eBay today and of course it was wrong, even though it was listed for all 800 Drifters, it was not close.

So now, after pulling it apart and draining the coolant, it's going back together while I order up the correct OEM replacement fan switch, then do it it all over again.

Should have known better than to buy replacement parts through eBay, trying to save a buck.  Not the first time this scarcity mentality wound up costing me more than it would have cost, had I done it right the first time.

Posted by CDNRatMan
 - April 28, 2018, 01:57:01 AM

  I have drained and cleaned both the rads on my 800's, used the water and whiter vinegar in both cases and as for refilling them not an issue, just let them burp and fill slowly to allow the air to escape, and check at the overflow tank, not hard.

Posted by Bucko
 - April 27, 2018, 23:14:59 PM

If you're going to drain the cooling system anyway, pull the sensor out and bench test it to see if it needs to be replaced.

Posted by greenbarn
 - April 27, 2018, 21:34:49 PM

I have flushed both my 800 and 1500, had no issues, didn't have to do anything special to bleed them out. 

Posted by Stroker Deuce
 - April 27, 2018, 18:56:46 PM

I rode slowly through the down town section of a neighboring city only to have the high temperature light of my 2001 800 come on.  The radiator fan was not running which helped isolate the issue.  Removing the seat and fuel tank I checked the fuse then located the connectors for the fan and fan switch sensor.  Bypassing the sensor, the fan ran well which isolated the problem to the fan switch sensor.  This item from Ebay will be here this next week https://www.ebay.com/itm/RADIATOR-FAN-SWITCH-SENSOR-Fits-KAWASAKI-VN800-VULCAN-800-DRIFTER-1999-2006/281829373251?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649 so I should be back on the road shortly there after.

My plan is to drain the cooling system before I replace the sensor, then flush the system with white vinegar and distilled water before replacing the coolant.

Does anyone have sage advice with any or all of this project?  Has anyone had issues with air getting trapped in the cooling system when refilling with coolant?  Any pitfalls I need to look out for?

SMF spam blocked by CleanTalk