Post reply

The message has the following error or errors that must be corrected before continuing:
Warning: this topic has not been posted in for at least 180 days.
Unless you're sure you want to reply, please consider starting a new topic.
Attachments: (Clear attachments)
Restrictions: 6 per post (6 remaining), maximum total size 64.00 MB, maximum individual size 29.30 MB
Uncheck the attachments you no longer want attached
Click or drag files here to attach them.
(Clear attachments)
Other options
Shortcuts: ALT+S post or ALT+P preview

Topic summary

Posted by LarryInSeattle
 - December 26, 2015, 00:43:56 AM

I am going to be selling this seat.  It has the horseshoe install.  You will need your stand offs from your seat to install it.  Simple to do.

$350 shipped to anywhere in the USA.  Pick it up in Seattle for $300.  It is a Corbin that built the seat on top of the factory seat pan.  Big difference in comfort.

Posted by LarryInSeattle
 - October 04, 2015, 13:33:55 PM

I started with the stock solo seat.  I bought a factory 2 up Corbin covered seat that was manufactured with the factory seat pan.  NOTE:  Different than the Corbin two up seat.

The stand up clips were the same.

Posted by Sand Storm
 - September 30, 2015, 18:52:30 PM

That would be sweet, one less challenge to worry about. Now I have to figure out what color, then bags. 

Posted by greenbarn
 - September 29, 2015, 21:52:03 PM

If you find a Corbin solo, it should bolt directly on your bike.

Posted by Sand Storm
 - September 28, 2015, 21:36:35 PM

I am considering buying a Corbin solo seat for my 800 Drifter, my concern is mounting it since my bike came with the 2up seat. Does anyone know if the Corbin seat will mount directly to the frame or do I need those solo seat frame fittings.  I would hate to spend all that cash and still not be able to install the Corbin seat.

Posted by aralph
 - July 17, 2015, 19:27:23 PM

Will get that for you.
You wouldn't happening to be going to Drift-In?

aralph

Posted by florencetkd
 - July 17, 2015, 15:46:09 PM

Hey My zip is 29501 can you get the shipping cost. I bought the brackets to attach the frame these will attach from the stock solo seat to the frame bracket correct? they look similar to the ones off of the stock 2 up seat.

Posted by aralph
 - May 12, 2015, 17:35:23 PM

Yes, for an 800, there is a 6mm weld nut attached to the bracket.
A 1500 brkt doesn't have the nut.
Email me your address and I can get you a cost.

aralph

Posted by florencetkd
 - May 12, 2015, 13:55:22 PM

These look right you made them for a 800 drifter?
Ill take a set please let me know how much shipping will be.
Thanks James

Posted by aralph
 - May 11, 2015, 18:26:06 PM

Here is a pic of the brackets I made up.

Posted by aralph
 - April 28, 2015, 22:12:20 PM

Hi James,

http://www.vulcandrifterriders.com/forum/index.php?topic=25155.msg54406#msg54406

If you are looking for the 2 "L brkts", I have several sets that I
fabbed up at work a while ago.

aralph

Posted by chief
 - April 28, 2015, 15:15:43 PM

The Corbin seat for the 800 comes with an integral "horseshoe" bracket. Otherwise you need that for the installation.

Drawing for the 800 is at the bottom of this page...
http://www.vulcandrifterriders.com/solo2dbl.html
Remember to check out the mods/tips forum folder and the REFERENCES Nav button at the top of every page.
Posted by LarryInSeattle
 - April 28, 2015, 03:42:06 AM

The two up bracket is different than the solo seat bracket.  However, if you have a factory 2 up seat, you must dissemble that seat and use some of those parts to use the solo seat. 

Posted by greenbarn
 - April 27, 2015, 08:38:41 AM

Yea, you probably have to move over the brackets to the other seat.   

Posted by CDNRatMan
 - April 27, 2015, 05:48:12 AM

  I'll take a stab in the dark here and say that the mount from the 2 up seat is also the mount for the solo seat.

SMF spam blocked by CleanTalk